Axis Communications Q1604 user manual UPnPTM, RTP/H.264, Bonjour

Page 48

AXIS Q1604 Network Camera

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 41. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 52.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Axis Q1604 Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1604 Network CameraConnectors Performance Considerations Hardware Overview Hardware OverviewConnectors and Buttons Network ConnectorConnector For technical specifications, seeLED Indicators Power ConnectorAudio Connector SD Card SlotHardware Overview Status LED Behavior for Focus Assistant Replacing the lensColor Green Amber RedAccessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariAccessing the Product Access from the Internet Set the Root PasswordClick Use Https Configure Capture Mode Live ViewControls on the Live View Manual TriggerGo to Setup Events Axis Media Control viewer toolbarTo show the manual trigger buttons in the Live View AMC Audio ControlsHow to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingSetting Up the Product Setting Up the ProductBasic Setup Adjust FocusSetting Up the Product Focus Assistant Video and Audio Video and AudioVideo Stream Pixel CounterPixel counter can be accessed from Click Save to apply the new settingsImage 264Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings Stream ProfilesExposure Settings Image AppearanceWhite Balance Wide Dynamic RangeOverlay Shutter & GainSet Shutter to IR cut filterPrivacy Mask Overlay ImageGo to Video & Audio Overlay Image Video and Audio Audio Settings Audio ModesAudio Input Audio Clips Audio OutputLive View Config Live View ConfigDefault Viewer for Browsers Viewer Settings Go to Setup Live View ConfigUser Defined Links Output ButtonsFor more information about I/O ports, see I/O Ports, on Detectors DetectorsCamera Tampering Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersDefault values Audio DetectionLow level 0% Recommended valuesInstall Application ApplicationsApplications Application LicensesAxis Q1604 Network Camera Events EventsSetting Up an Action Rule Go to Events Action Rules and click AddSetting Up an Email Recipient Events RecipientsRecipient Use with action Go to Events Recipients and click AddSchedules RecurrencesTo create a new schedule Go to Events Schedules and click AddRecordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time Audio SupportBasic TCP/IP Settings System Options NetworkAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 BonjourSystem Options Storage SD CardNetwork Share Go to System Options Storage and click SD CardMaintenance Ports & DevicesPorts Port StatusSystem Options Support AdvancedReset to Factory Default Settings Plain ConfigFile Upload Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with streaming H.264Basic Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalSetup Video & Audio Camera Settings SettingsStorage and disk management problems Storage disruptionRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Technical SpecificationsFunction/group Specifications Audio Audio streaming Microphone Specification Network SecurityInput/output Audio input Audio outputConnectors Pin terminal block for power input Mm audio connectors stereoTo max 40 V DC To deactivate Digital OutputPerformance Considerations Audio Input Audio OutputTip Microphone/Line Line out mono Ring Sleeve Ground M3.4

Q1604 specifications

The Axis Communications Q1604 is a powerful and versatile network camera designed for professional surveillance applications in various environments. Renowned for its high-quality imaging and robust performance, the Q1604 is engineered to deliver clear and detailed visuals, making it an ideal choice for security professionals.

One of the standout features of the Q1604 is its exceptional image quality, which is powered by advanced image sensor technology. It boasts an impressive resolution of 1920 x 1080 pixels, capturing Full HD video at 30 frames per second. This ensures that users receive sharp and clear images, even in challenging lighting conditions. The camera is equipped with Axis’ Lightfinder technology, allowing it to perform exceptionally well in low-light environments. This feature makes it suitable for 24/7 surveillance, delivering color images in near darkness.

The Q1604 also incorporates Wide Dynamic Range (WDR) technology, which enhances its ability to handle scenes with varying light levels. This is particularly useful in situations where bright sunlight and shadows coexist, allowing the camera to produce a balanced and detailed image. This ensures that critical details are not lost, enhancing overall situational awareness.

Another important aspect of the Q1604 is its flexible installation options. The camera supports Power over Ethernet (PoE), allowing it to receive power and network connectivity through a single cable. This reduces installation complexity and costs. Additionally, the camera features adjustable lenses, which provide the ability to customize the field of view according to specific surveillance needs.

Security is paramount in surveillance technology, and the Q1604 is designed with multiple security features to protect data integrity. It offers encrypted video transmission and password protection, ensuring that unauthorized users cannot access the system. Furthermore, the camera is compatible with a range of video management software (VMS) for integration into existing security ecosystems.

In conclusion, the Axis Communications Q1604 is a feature-rich network camera offering robust performance, high-resolution imaging, and advanced technologies. Its adaptability to varying lighting conditions, ease of installation, and strong security features make it one of the leading choices for professional surveillance solutions, catering to the demands of various industries while ensuring reliable monitoring and protection.
Top Page Image Contents