Axis Communications P5512 PTZ Multi-Connector Cable sold separately, Function Pin Specifications

Page 53

AXIS P5512 PTZ Dome Network Camera

Multi-Connector Cable (sold separately)

Multi-Connector Cable (sold separately)

When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller.

Connect the multi-connector cable to the product’s multi-connector. To locate the multi-connector, see Hardware Overview, on page

6 . The cable provides the following connectors:

Power connector - 3-pin terminal block used for power input. See image below. Use a limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for the audio out.

I/O terminal connector - Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to ground and auxiliary power, the I/O terminal connector provides the interface to:

•Digital output — For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Port & Devices > Port Status) if the alarm device is activated.

•Digital input — An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Port & Devices > Port Status).

Function

Pin

Notes

Specifications

 

 

 

 

GND

1

Ground

 

 

 

 

 

3.3 V DC Power

2

Can be used to power auxiliary equipment.

Max load:

 

 

Note: This pin can only be used as power out.

250 mA

 

 

 

 

Configurable (Input

3–6

Digital input — Connect to GND to activate, or leave

0 to +40 V DC

or Output)

 

floating (unconnected) to deactivate.

 

 

 

 

 

 

 

Digital output — Internal connection to ground when

Max load:

 

 

activated, floating (unconnected) when deactivated. If

100 mA

 

 

used with an external relay, a diode must be connected

Max voltage:

 

 

in parallel with the load, for protection against voltage

 

 

+40 V DC

 

 

transients.

 

 

 

 

 

 

 

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Axis P5512 PTZ Dome Network Camera Legal Considerations About this documentLiability Intellectual Property RightsLearn More SupportAxis P5512 PTZ Dome Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Hardware OverviewHardware Overview Connectors and Buttons Color Indication Hardware Overview LED IndicatorsAccessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariSet the Root Password Accessing the Product Access from the InternetLive View Controls on the Live ViewAxis Media Control viewer toolbar Go to Setup EventsManual Trigger To show the manual trigger buttons in the Live ViewAMC Audio Controls PTZ ControlsAxis P5512 PTZ Dome Network Camera Media Streams How to Stream H.264Media Streams Axis Media Control AMCQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsBasic Setup Setting Up the ProductSetting Up the Product Video and Audio Video and AudioVideo Stream Pixel CounterStream Profiles Click Save to apply the new settingsImage 264Exposure Settings Camera SettingsImage Appearance White BalanceOverlay Image Image SettingsOverlay Using Overlay Text in an Action Rule Audio SettingsAudio Modes Go to Events Action RulesAudio Input Audio Output Audio ClipsDefault Viewer for Browsers Live View ConfigLive View Config Go to Setup Live View Config Viewer SettingsUser Defined Links Output ButtonsAxis P5512 PTZ Dome Network Camera Go to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomGuard Tour PTZ Pan Tilt Zoom GatekeeperOsdi Zones Go to PTZ Guard Tour and click AddPTZ Pan Tilt Zoom Advanced Operator Same as administrator but with lower priorityControl Queue LimitsDetectors Set Up Motion Detection WindowsDetectors Motion DetectionMotion Detection Parameters Audio DetectionApplications Install ApplicationApplications Application LicensesAxis P5512 PTZ Dome Network Camera Events EventsTime Setting Up an Action RulePTZ Control Go to Events Action Rules and click AddGo to Events Recipients and click Add RecipientsRecipient Use with action Schedules Setting Up an Email RecipientRecurrences Go to Events Schedules and click AddRecordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Go to Setup System Options Security Certificates To install a self-signed certificateClick Install certificate and upload the certificate Date & TimeSystem Options Network Basic TCP/IP SettingsAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 BonjourPorts & Devices System Options StorageSupport MaintenanceSupport Overview System OverviewPlain Config Reset to Factory Default SettingsScripting File UploadAxis P5512 PTZ Dome Network Camera Function Pin Specifications Multi-Connector Cable sold separatelyMulti-Connector Cable sold separately Connector Troubleshooting TroubleshootingTo upgrade, follow these instructions Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Troubleshooting Emergency Recovery ProcedureProblems setting the IP address Product cannot be accessed from a browserBasic Product is accessible locally but not externallyProblems with streaming H.264 Setup Video & Audio Camera Settings Video and image problems, generalSettings Storage and disk management problemsTechnical Specifications Technical SpecificationsInstallation Function/group Specifications Network SecurityMaintenance General Casing Memory PowerPerformance Considerations ConnectorsM4.4
Top Page Image Contents