Axis Communications Q6045-C PTZ user manual Control Queue

Page 31

AXIS Q6045-C PTZ Dome Network Camera

PTZ (Pan Tilt Zoom)

The Panel Shortcut Command Buttons list shows the user-defined buttons that can be accessed from the Live View page’s Ctrl panel. These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command button.

The following PTZ controls are enabled by default:

•Pan control

•Tilt control

•Zoom control

•Focus control

•Iris control

To disable specific controls, deselect the options under Enable/Disable controls.

Note

Disabling PTZ controls will not affect preset positions. For example, if the tilt control is disabled, the product can still move to preset positions that require a tilt movement.

Control Queue

The administrator can set up a queue for PTZ controllers from PTZ > Control Queue. Once set up, the PTZ Control Queue buttons appear in the Live View page offering one viewer exclusive control for a limited period of time. Other users will be placed in queue.

A user who belongs to a group (see Users on page 44) with a higher PTZ priority can go before other users in the queue and take control of the product. The order of priority is as follows:

1.Administrator — An administrator takes over PTZ control regardless of who is first in queue. The administrator will be removed from the queue 60 seconds after the last PTZ control command.

2.Event — The Axis product can be configured to go to a preset position when triggered by an alarm (see Events on page 37). The event will immediately be placed first in the queue except when an administrator is in control.

3.Operator — Same as administrator but with lower priority

4.Guard Tour — A guard tour (see page 29) has PTZ control for an indefinite period of time. It may be overridden by an operator, event or administrator. The guard tour will resume when higher priority groups leave the queue.

5.Viewer — Multiple viewers must wait for their turn. The viewer has 60 seconds PTZ control before control is passed on to the next viewer in queue.

Note

•The administrator can enable and disable PTZ controls for selected users.

•To identify different users in the viewer group, cookies must be enabled on the client.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Axis Q6045-C PTZ Dome Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q6045-C PTZ Dome Network Camera Table of ContentsMulti-Connector Cable Troubleshooting Camera Connectors and ButtonsFor technical specifications, see Hardware OverviewSD Card Slot LED IndicatorsMulti-connector Power ButtonMedia Converter Switch Connectors Media Converter SwitchDip switch position Network Connector Dip SwitchesConnector internal 2-pin I/O terminal block Description Media Converter Switch LED IndicatorsSet the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Go to Setup EventsLive View Controls on the Live ViewPTZ Controls Axis Media Control viewer toolbarTo show the manual trigger buttons in the Live View Axis Q6045-C PTZ Dome Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis Q6045-C PTZ Dome Network Camera Basic Setup Set Up the ProductPixel Counter Click Save to apply the new settingsVideo Video Stream264 Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceGo to Video Video Stream and select the Image tab Image SettingsOverlay Overlay ImageGo to Events Action Rules Use Overlay Text in an Action RulePrivacy Mask Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGatekeeper Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomMax Limits ConfigurationAutotracking Exclude AreasTo add a recorded tour Guard TourTour Recording To add a guard tourControls Osdi ZonesAdvanced LimitsControl Queue Operator Same as administrator but with lower priorityMotion Detection Set Up Motion Detection WindowsDetectors Shock DetectionEnter/Exit Detector Object RemovedObject Counter Fence DetectorApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q6045-C PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesTriggers Actions Add RecipientsRecipient Types Recipient Use with action Set Up Email RecipientsGo to Events Schedules and click Add Set Up RecurrencesCreate Schedules To create a new scheduleGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis Q6045-C PTZ Dome Network Camera Green/white Ethernet receiving Multi-Connector CableFunction Pin wire Specifications Activated, floating unconnected when Drain, 100 mACheck the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsRe-mount the storage device Storage and disk management problemsMedia converter switch Storage disruptionTechnical Specifications Power Function/group Specifications System ApplicationInstallation aid MaintenanceIncluded Function/group SpecificationsWeight AccessoriesCamera Connectors ConnectorsExternal Connectors Separately DC, min 75 W DC output Power out DC, 50 mADC input Max load = 7 aM4.2

Q6045-C PTZ specifications

The Axis Communications Q6045-C PTZ camera is a state-of-the-art surveillance solution designed for demanding environments. Known for its exceptional performance, this camera combines advanced technology with robust features, making it an ideal choice for various applications, including city surveillance, traffic monitoring, and large infrastructure protection.

One of the key features of the Q6045-C is its high-quality imaging capabilities. Equipped with a 2 MP sensor, it offers stunning video resolution at 1080p, delivering sharp and clear images even in challenging lighting conditions. This camera has a wide dynamic range (WDR) technology, ensuring that both bright and dark areas are captured with precision, making it highly effective in situations with varying light conditions.

The Q6045-C also boasts advanced pan-tilt-zoom (PTZ) functionality, allowing operators to cover large areas with great detail. It offers a 360-degree continuous pan and a tilt range of up to 20 degrees, coupled with a powerful 30x optical zoom. This flexibility enables security personnel to monitor specific areas and zoom in on points of interest without losing image quality, ensuring that no detail goes unnoticed.

Another notable technological advancement of this camera is its built-in Axis Zipstream technology. This feature optimizes bandwidth and storage efficiency by dynamically adjusting the compression of video streams while maintaining essential details. This allows users to save on storage costs and simplifies bandwidth management, making the Q6045-C an economical choice for long-term surveillance.

The Q6045-C is built to withstand harsh environments, featuring an IP66 rating for weather resistance and a robust design that protects against dust and water ingress. This durability makes it suitable for outdoor use in various climates.

Additionally, the camera is equipped with advanced cybersecurity features to safeguard against unauthorized access and tampering. With Axis Communications’ commitment to security, users can rest assured that their surveillance data remains protected.

In summary, the Axis Communications Q6045-C PTZ camera is a versatile and robust surveillance solution featuring high-resolution imaging, advanced PTZ capabilities, and enhanced durability. Its smart technologies, including Zipstream and cybersecurity measures, make it a reliable choice for ensuring safety and security in a wide range of applications.
Top Page Image Contents