Axis Communications Q6045-C PTZ Storage and disk management problems, Storage disruption

Page 61

AXIS Q6045-C PTZ Dome Network Camera

Troubleshooting

Storage and disk management problems

Storage disruption

A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other

 

read or write problems occur. To identify the source of the problem, check the System Log under

 

System Options > Support > Logs & Reports. Depending on the problem, it might be necessary to

 

re-mount the storage device.

 

For information on how to set up a storage disruption alarm, see Events on page 37.

Video cannot be recorded

Check that the SD card is not write protected (that is, read only).

SD card cannot be mounted

Reformat the SD card and then click Mount.

 

 

 

NOTICE

 

 

Formatting the card will remove all content, including all recordings, from the SD card.

Media converter switch

 

 

 

 

Media converter switch

The media converter switch does not support hotswapping. Disconnect power from the switch

freezes after hotswapping

before swapping cameras. Restart the switch after a failed attempt to hotswap.

61

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Axis Q6045-C PTZ Dome Network Camera Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis Q6045-C PTZ Dome Network Camera Table of ContentsMulti-Connector Cable Troubleshooting For technical specifications, see Connectors and ButtonsHardware Overview CameraMulti-connector LED IndicatorsPower Button SD Card SlotMedia Converter Switch Connectors Media Converter SwitchDip switch position Network Connector Dip SwitchesConnector internal 2-pin I/O terminal block Description Media Converter Switch LED IndicatorsAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordLive View Go to Setup EventsControls on the Live View Click Use HttpsPTZ Controls Axis Media Control viewer toolbarTo show the manual trigger buttons in the Live View Axis Q6045-C PTZ Dome Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis Q6045-C PTZ Dome Network Camera Basic Setup Set Up the ProductVideo Click Save to apply the new settingsVideo Stream Pixel Counter264 Stream ProfilesExposure Settings Camera SettingsImage Appearance White BalanceOverlay Image SettingsOverlay Image Go to Video Video Stream and select the Image tabGo to Events Action Rules Use Overlay Text in an Action RulePrivacy Mask Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons For more information about I/O ports, see I/O Ports onGo to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom GatekeeperAutotracking ConfigurationExclude Areas Max LimitsTour Recording Guard TourTo add a guard tour To add a recorded tourAdvanced Osdi ZonesLimits ControlsControl Queue Operator Same as administrator but with lower priorityDetectors Set Up Motion Detection WindowsShock Detection Motion DetectionEnter/Exit Detector Object RemovedObject Counter Fence DetectorGo to Setup Applications Install ApplicationApplications Application LicensesAxis Q6045-C PTZ Dome Network Camera Events Set Up Action RulesConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers Actions Add RecipientsRecipient Types Recipient Use with action Set Up Email RecipientsCreate Schedules Set Up RecurrencesTo create a new schedule Go to Events Schedules and click AddRecording List RecordingsContinuous Recording Go to Recordings ListLanguages Security System OptionsUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee Go to Setup System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkIPv6 Address Configuration IPv4 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4Smtp email QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 BonjourSD Card StorageMount and Unmount SD Card Format SD CardPorts & Devices MaintenanceNetwork Share PortsSupport Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsScripting File UploadAxis Q6045-C PTZ Dome Network Camera Function Pin wire Specifications Multi-Connector CableActivated, floating unconnected when Drain, 100 mA Green/white Ethernet receivingUpgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Video Camera Settings Key framesMedia converter switch Storage and disk management problemsStorage disruption Re-mount the storage deviceTechnical Specifications Installation aid Function/group Specifications System ApplicationMaintenance PowerWeight Function/group SpecificationsAccessories IncludedCamera Connectors ConnectorsExternal Connectors DC input DC output Power out DC, 50 mAMax load = 7 a Separately DC, min 75 WM4.2

Q6045-C PTZ specifications

The Axis Communications Q6045-C PTZ camera is a state-of-the-art surveillance solution designed for demanding environments. Known for its exceptional performance, this camera combines advanced technology with robust features, making it an ideal choice for various applications, including city surveillance, traffic monitoring, and large infrastructure protection.

One of the key features of the Q6045-C is its high-quality imaging capabilities. Equipped with a 2 MP sensor, it offers stunning video resolution at 1080p, delivering sharp and clear images even in challenging lighting conditions. This camera has a wide dynamic range (WDR) technology, ensuring that both bright and dark areas are captured with precision, making it highly effective in situations with varying light conditions.

The Q6045-C also boasts advanced pan-tilt-zoom (PTZ) functionality, allowing operators to cover large areas with great detail. It offers a 360-degree continuous pan and a tilt range of up to 20 degrees, coupled with a powerful 30x optical zoom. This flexibility enables security personnel to monitor specific areas and zoom in on points of interest without losing image quality, ensuring that no detail goes unnoticed.

Another notable technological advancement of this camera is its built-in Axis Zipstream technology. This feature optimizes bandwidth and storage efficiency by dynamically adjusting the compression of video streams while maintaining essential details. This allows users to save on storage costs and simplifies bandwidth management, making the Q6045-C an economical choice for long-term surveillance.

The Q6045-C is built to withstand harsh environments, featuring an IP66 rating for weather resistance and a robust design that protects against dust and water ingress. This durability makes it suitable for outdoor use in various climates.

Additionally, the camera is equipped with advanced cybersecurity features to safeguard against unauthorized access and tampering. With Axis Communications’ commitment to security, users can rest assured that their surveillance data remains protected.

In summary, the Axis Communications Q6045-C PTZ camera is a versatile and robust surveillance solution featuring high-resolution imaging, advanced PTZ capabilities, and enhanced durability. Its smart technologies, including Zipstream and cybersecurity measures, make it a reliable choice for ensuring safety and security in a wide range of applications.
Top Page Image Contents