Axis Communications Q6045-C PTZ user manual UPnPTM, RTP/H.264, Bonjour

Page 51

AXIS Q6045-C PTZ Dome Network Camera

System Options

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 44. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 55.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Axis Q6045-C PTZ Dome Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q6045-C PTZ Dome Network Camera Table of ContentsMulti-Connector Cable Troubleshooting Camera Connectors and ButtonsFor technical specifications, see Hardware OverviewSD Card Slot LED IndicatorsMulti-connector Power ButtonMedia Converter Switch Connectors Media Converter SwitchNetwork Connector Dip Switches Dip switch positionConnector internal 2-pin I/O terminal block Description Media Converter Switch LED IndicatorsSet the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Go to Setup EventsLive View Controls on the Live ViewAxis Media Control viewer toolbar PTZ ControlsTo show the manual trigger buttons in the Live View Axis Q6045-C PTZ Dome Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis Q6045-C PTZ Dome Network Camera Basic Setup Set Up the ProductPixel Counter Click Save to apply the new settingsVideo Video Stream264 Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceGo to Video Video Stream and select the Image tab Image SettingsOverlay Overlay ImageGo to Events Action Rules Use Overlay Text in an Action RulePrivacy Mask Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGatekeeper Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomMax Limits ConfigurationAutotracking Exclude AreasTo add a recorded tour Guard TourTour Recording To add a guard tourControls Osdi ZonesAdvanced LimitsControl Queue Operator Same as administrator but with lower priorityMotion Detection Set Up Motion Detection WindowsDetectors Shock DetectionEnter/Exit Detector Object RemovedObject Counter Fence DetectorApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q6045-C PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesTriggers Add Recipients ActionsRecipient Types Recipient Use with action Set Up Email RecipientsGo to Events Schedules and click Add Set Up RecurrencesCreate Schedules To create a new scheduleGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis Q6045-C PTZ Dome Network Camera Green/white Ethernet receiving Multi-Connector CableFunction Pin wire Specifications Activated, floating unconnected when Drain, 100 mACheck the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsRe-mount the storage device Storage and disk management problemsMedia converter switch Storage disruptionTechnical Specifications Power Function/group Specifications System ApplicationInstallation aid MaintenanceIncluded Function/group SpecificationsWeight AccessoriesConnectors Camera ConnectorsExternal Connectors Separately DC, min 75 W DC output Power out DC, 50 mADC input Max load = 7 aM4.2

Q6045-C PTZ specifications

The Axis Communications Q6045-C PTZ camera is a state-of-the-art surveillance solution designed for demanding environments. Known for its exceptional performance, this camera combines advanced technology with robust features, making it an ideal choice for various applications, including city surveillance, traffic monitoring, and large infrastructure protection.

One of the key features of the Q6045-C is its high-quality imaging capabilities. Equipped with a 2 MP sensor, it offers stunning video resolution at 1080p, delivering sharp and clear images even in challenging lighting conditions. This camera has a wide dynamic range (WDR) technology, ensuring that both bright and dark areas are captured with precision, making it highly effective in situations with varying light conditions.

The Q6045-C also boasts advanced pan-tilt-zoom (PTZ) functionality, allowing operators to cover large areas with great detail. It offers a 360-degree continuous pan and a tilt range of up to 20 degrees, coupled with a powerful 30x optical zoom. This flexibility enables security personnel to monitor specific areas and zoom in on points of interest without losing image quality, ensuring that no detail goes unnoticed.

Another notable technological advancement of this camera is its built-in Axis Zipstream technology. This feature optimizes bandwidth and storage efficiency by dynamically adjusting the compression of video streams while maintaining essential details. This allows users to save on storage costs and simplifies bandwidth management, making the Q6045-C an economical choice for long-term surveillance.

The Q6045-C is built to withstand harsh environments, featuring an IP66 rating for weather resistance and a robust design that protects against dust and water ingress. This durability makes it suitable for outdoor use in various climates.

Additionally, the camera is equipped with advanced cybersecurity features to safeguard against unauthorized access and tampering. With Axis Communications’ commitment to security, users can rest assured that their surveillance data remains protected.

In summary, the Axis Communications Q6045-C PTZ camera is a versatile and robust surveillance solution featuring high-resolution imaging, advanced PTZ capabilities, and enhanced durability. Its smart technologies, including Zipstream and cybersecurity measures, make it a reliable choice for ensuring safety and security in a wide range of applications.
Top Page Image Contents