Axis Communications M1114E IPv4 Address Configuration, IPv6 Address Configuration, ARP/Ping

Page 41

AXIS M1114–E

System Options

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 47) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see .

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

AXIS Video Hosting System (AVHS)

AVHS used in conjunction with an AVHS service, provides easy and secure Internet access to live and recorded video accessible from any location. For more information and help to find a local AVHS Service Provider go to www.axis.com/hosting

The AVHS settings are configured under System Options > Network > TCP IP > Basic. The possibility to connect to an AVHS service is enabled by default. To disable, clear the Enable AVHS box.

One-click enabled - Press and hold the product’s control button (see Hardware Overview on page 6 ) for about 3 seconds to connect to an AVHS service over the Internet. Once registered, Always will be enabled and the Axis product stays connected to the AVHS service. If the product is not registered within 24 hours from when the button is pressed, the product will disconnect from the AVHS service.

Always - The Axis product will constantly attempt to connect to the AVHS service over the Internet. Once registered the product will stay connected to the service. This option can be used when the product is already installed and it is not convenient to use the one-click installation.

AXIS Internet Dynamic DNS Service

AXIS Internet Dynamic DNS Service assigns a host name for easy access to the product. For more information, see www.axiscam.net

To register the Axis product with AXIS Internet Dynamic DNS Service, go to System Options > Network > TCP/IP > Basic. Under Services, click the AXIS Internet Dynamic DNS Service Settings button (requires access to the Internet). The domain name currently registered at AXIS Internet Dynamic DNS service for the product can at any time be removed.

Note

AXIS Internet Dynamic DNS Service requires IPv4.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Axis M1114-E Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis M1114-E Table of ContentsPerformance Considerations Network Connector Connectors and ButtonsHardware Overview Control ButtonPower LED Indication LED IndicatorsStatus LED Indication Network LED IndicationAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordClick Create self-signed certificate Set Power Line FrequencyLive View Controls on the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerPTZ Controls Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M1114-E Basic Setup Set Up the ProductFocus Adjustment Back Focus AdjustmentVideo Stream VideoPixel Counter Image264 Click Save to apply the new settingsStream Profiles Exposure Settings Camera SettingsView Area Image AppearanceOverlay Image OverlayGo to Video Video Stream and select the Image tab Go to Video Overlay ImageGo to Events Action Rules Use Overlay Text in an Action RulePrivacy Mask Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Guard Tour Preset PositionsPTZ Pan Tilt Zoom Advanced Operator Same as administrator but with lower priorityControl Queue ControlsCamera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis M1114-E Go to Setup Applications Install ApplicationApplications Application LicensesAxis M1114-E Events Set Up Action RulesConvert Event Types to Action Rules Go to Events Action Rules and click AddActions TriggersRecipient Types Add RecipientsGo to Events Recipients and click Add Recipient Use with actionSet Up Email Recipients Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddAxis M1114-E Recording List RecordingsContinuous Recording Go to Recordings ListLanguages Security System OptionsUsers IP Address FilterGo to System Options Security Ieee IeeeCertificates Go to Setup System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkIPv6 Address Configuration IPv4 Address ConfigurationAxis Internet Dynamic DNS Service ARP/PingDNS Configuration Advanced TCP/IP SettingsNTP Configuration Host Name ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM can be disabled under System Options Network UPnPTM QoS Quality of ServiceUPnPTM RTP/H.264Storage MaintenanceBonjour Network ShareSupport Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsScripting File UploadUpgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Problems with streaming H.264Video and image problems, general Video Camera SettingsStorage disruption Storage and disk management problemsRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Installation Function/group Specifications System ApplicationMaintenance General Casing PowerPerformance Considerations M2.5
Top Page Image Contents