Axis Communications M1145L user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 47

AXIS M1145–L Network Camera

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 40. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 51.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

The Axis product supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card with speed class 10.

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The Axis product supports SD cards with the following file systems:

47

Image 47
Contents Axis M1145-L Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M1145-L Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Connectors and ButtonsNetwork Connector ConnectorColor Indication LED IndicatorsSD Card Slot Control ButtonAccess from the Internet Accessing the ProductAccessing the Product Access from a BrowserClick Use Https Set Power Line FrequencyLive View Controls on the Live ViewManual Trigger Go to Setup EventsAxis Media Control viewer toolbar PTZ ControlsAxis M1145-L Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Axis M1145-L Network Camera Focus & Zoom Setting Up the ProductSetting Up the Product Basic SetupAxis M1145-L Network Camera Image Setting Up the Product VideoVideo Stream Pixel Counter264 Camera SettingsStream Profiles Wide Dynamic Range Exposure SettingsImage Appearance White BalanceDay/Night Iris configurationIris adjustment Built-in IR Illuminations LEDsGo to Video View Area Setting Up the Product View AreaSelect an Aspect ratio and a Video stream resolution OverlayGo to Events Action Rules Using Overlay Text in an Action RuleOverlay Image Go to Video Overlay ImagePrivacy Mask Viewer Settings Live View ConfigLive View Config Default Viewer for BrowsersOutput Buttons Go to Setup Live View ConfigUser Defined Links Light ButtonsGuard Tour Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomControls AdvancedControl Queue Tour RecordingMotion Detection DetectorsDetectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis M1145-L Network Camera Application Licenses Install ApplicationApplications ApplicationsAxis M1145-L Network Camera Events EventsGo to Events Action Rules and click Add Setting Up an Action RulePTZ Control Go to Events Recipients and click Add RecipientsFallback Action Recipient Use with actionGo to Events Schedules and click Add Setting Up an Email RecipientSchedules RecurrencesAxis M1145-L Network Camera Continuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityGo to System Options Security Ieee IeeeCertificates Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Go to System Options Storage Click Network Share Network ShareGo to System Options Storage and click SD Card Support MaintenanceSystem Options Ports & Devices File Upload System OverviewLogs & Reports ScriptingPlain Config Reset to Factory Default SettingsChecking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserVideo Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalStorage disruption Storage and disk management problemsTechnical Specifications Technical SpecificationsPower Function/group Specifications System ApplicationInstallation Maintenance General CasingFunction Pin Specifications ConnectorsAccessories Decoder 1-user license Video WarrantyPerformance Considerations M2.2