Axis Communications M1054 Axis Media Control viewer toolbar, PTZ Controls, AMC Audio Controls

Page 11

AXIS M1054 Network Camera

Access the Product

For more information about action rules, see Events on page 34.

To show the manual trigger buttons in the Live View page:

1.Go to Setup > Live View Config .

2.Under Action Buttons, select Show manual trigger button.

AXIS Media Control viewer toolbar

The AXIS Media Control viewer toolbar is available in Internet Explorer only. See AXIS Media Control (AMC) on page 13 for more information. The toolbar displays the following buttons:

The Play button connects to the Axis product and starts playing a media stream.

The Stop button stops the media stream.

The Snapshot button takes a snapshot of the video image. The location where the image is saved can be specified in the AMC Control Panel.

Click the View Full Screen button and the video image will fill the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view.

The Record button is used to record the current video stream. The location where the recording is saved can be specified in the AMC Control Panel. Enable this button from Live View Config > Viewer Settings.

AMC Audio Controls

AMC audio buttons control the speakers and microphone connected to the client computer. The buttons are only visible when audio is enabled.

Speaker button — Click to turn the speakers on or off.

Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission.

Use the slider to control the volume of the speakers and the microphone.

Half-duplex mode

The Talk/Listen button is used to switch between sending and receiving audio. The button can be configured from the Audio tab in the AMC Control panel:

•Push-To-Talk mode: Click and hold the button to talk/send. Release the button to listen.

•Toggle mode: Click once to switch between talking and listening.

Simplex – speaker only mode

To send audio, the Talk and Microphone buttons must both be active. Click either button to stop audio transmission.

PTZ Controls

The Live View page also displays Pan/Tilt/Zoom (PTZ) controls. The administrator can enable/disable controls for specified users under System Options > Security > Users.

Note

These controls are available if digital PTZ is enabled in the selected view area, see View Area on page 19.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Axis M1054 Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis M1054 Network Camera Table of ContentsConnectors Performance Considerations TroubleshootingHardware Overview Connectors and ButtonsNetwork Connector ConnectorControl Button LED IndicatorsPower Connector Set the Root Password Access the ProductAccess from a Browser Access from the InternetClick Create self-signed certificate Set Power Line FrequencyLive View Manual Trigger Go to Setup EventsControls on the Live View AMC Audio Controls Axis Media Control viewer toolbarPTZ Controls Axis M1054 Network Camera Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductImage Video and AudioVideo Stream Pixel Counter264 Click Save to apply the new settingsStream Profiles Image Appearance Camera SettingsExposure Settings View AreaGo to Video & Audio Video Stream and select the Image tab OverlayOverlay Image Go to Events Action Rules Use Overlay Text in an Action RuleGo to Video & Audio Overlay Image Audio Input Audio SettingsPrivacy Mask Audio ModesAudio Output Audio ClipsBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsOutput Buttons Go to Setup Live View ConfigUser Defined Links Light ButtonsGuard Tour Preset PositionsPTZ Pan Tilt Zoom Controls Operator Same as administrator but with lower priorityAdvanced Control QueueAxis M1054 Network Camera Go to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsGo to Events Action Rules and click Add Audio DetectionPIR Sensor Go to Detectors Audio DetectionApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis M1054 Network Camera Convert Event Types to Action Rules Set Up Action RulesEvents Triggers Recipient Types Add RecipientsActions Go to Events Schedules and click Add Set Up Email RecipientsCreate Schedules Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingClick Save to save and start the recording Languages IP Address Filter System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Ports & Devices MaintenanceStorage Logs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingCheck the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserSetup Video & Audio Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Supported Function/group Specifications SecurityInstallation Maintenance Installation aidsConnectors Performance Considerations M3.7
Related manuals
Manual 114 pages 25.17 Kb

M1054 specifications

Axis Communications has firmly established itself as a leader in the network video surveillance market, offering a wide array of innovative products that cater to various security requirements. One of its noteworthy offerings is the Axis M1054 network camera, which is designed to provide reliable surveillance capabilities while incorporating advanced technologies and features.

The Axis M1054 is a fixed network camera that is particularly well-suited for indoor use. It boasts a compact design that allows for seamless integration into various environments, making it ideal for retail stores, offices, and other commercial spaces. One of its standout features is the ability to deliver high-resolution video, with a 1280x800 resolution at 30 frames per second, ensuring clear and detailed images for effective monitoring.

Equipped with a progressive scan CMOS sensor, the M1054 enhances image quality, providing sharp and vibrant colors. In low-light conditions, the camera continues to perform effectively thanks to its advanced light sensitivity. The built-in electronic day/night functionality automatically adjusts to changing lighting conditions, enabling the camera to maintain high-quality video during both day and night.

In terms of connectivity, the Axis M1054 supports Power over Ethernet (PoE), simplifying installation and reducing cable clutter. This feature allows the camera to receive both power and data through a single Ethernet cable, enabling more flexible placement options. The camera also includes an SD card slot for local storage, providing added redundancy and ensuring critical footage is retained even if network connectivity is lost.

Axis Communications places a strong emphasis on security, and the M1054 is no exception. It features robust security measures, including password protection, IP address filtering, and HTTPS encryption. These features provide a critical layer of defense against unauthorized access, ensuring that recorded video remains secure.

Moreover, the M1054 is compatible with Axis’ wide array of video management software and third-party systems, providing users the flexibility to integrate their surveillance solution into a broader security ecosystem. With its advanced features, reliable performance, and user-friendly design, the Axis M1054 network camera represents an excellent choice for businesses looking to enhance their security measures and ensure peace of mind.
Top Page Image Contents