Axis Communications M1054 user manual Network, Basic TCP/IP Settings

Page 45

AXIS M1054 Network Camera

System Options

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 52) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 45.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>

45

Image 45
Contents Axis M1054 Network Camera Legal Considerations About this documentLiability Intellectual Property RightsLearn More SupportAxis M1054 Network Camera Table of ContentsConnectors Performance Considerations TroubleshootingNetwork Connector Connectors and ButtonsConnector Hardware OverviewLED Indicators Power ConnectorControl Button Access from a Browser Access the ProductAccess from the Internet Set the Root PasswordSet Power Line Frequency Live ViewClick Create self-signed certificate Go to Setup Events Controls on the Live ViewManual Trigger Axis Media Control viewer toolbar PTZ ControlsAMC Audio Controls Axis M1054 Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductVideo Stream Video and AudioPixel Counter ImageClick Save to apply the new settings Stream Profiles264 Exposure Settings Camera SettingsView Area Image AppearanceOverlay Overlay ImageGo to Video & Audio Video Stream and select the Image tab Use Overlay Text in an Action Rule Go to Video & Audio Overlay ImageGo to Events Action Rules Privacy Mask Audio SettingsAudio Modes Audio InputAudio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigLight Buttons Output ButtonsPreset Positions PTZ Pan Tilt ZoomGuard Tour Advanced Operator Same as administrator but with lower priorityControl Queue ControlsAxis M1054 Network Camera Camera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsPIR Sensor Audio DetectionGo to Detectors Audio Detection Go to Events Action Rules and click AddGo to Setup Applications Install ApplicationApplications Application LicensesAxis M1054 Network Camera Set Up Action Rules EventsConvert Event Types to Action Rules Triggers Add Recipients ActionsRecipient Types Set Up Email Recipients Create SchedulesGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesRecording List RecordingsContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages Security System OptionsUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Click Install certificate and upload the certificate Go to Setup System Options Security CertificatesDate & Time Audio SupportNetwork Basic TCP/IP SettingsAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 BonjourMaintenance StoragePorts & Devices Support Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsScripting File UploadUpgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Problems with streaming H.264Video and image problems, general Setup Video & Audio Camera SettingsStorage and disk management problems SettingsNo audio Poor audio qualityTechnical Specifications Installation Function/group Specifications SecurityMaintenance Installation aids SupportedConnectors Performance Considerations M3.7
Related manuals
Manual 114 pages 25.17 Kb

M1054 specifications

Axis Communications has firmly established itself as a leader in the network video surveillance market, offering a wide array of innovative products that cater to various security requirements. One of its noteworthy offerings is the Axis M1054 network camera, which is designed to provide reliable surveillance capabilities while incorporating advanced technologies and features.

The Axis M1054 is a fixed network camera that is particularly well-suited for indoor use. It boasts a compact design that allows for seamless integration into various environments, making it ideal for retail stores, offices, and other commercial spaces. One of its standout features is the ability to deliver high-resolution video, with a 1280x800 resolution at 30 frames per second, ensuring clear and detailed images for effective monitoring.

Equipped with a progressive scan CMOS sensor, the M1054 enhances image quality, providing sharp and vibrant colors. In low-light conditions, the camera continues to perform effectively thanks to its advanced light sensitivity. The built-in electronic day/night functionality automatically adjusts to changing lighting conditions, enabling the camera to maintain high-quality video during both day and night.

In terms of connectivity, the Axis M1054 supports Power over Ethernet (PoE), simplifying installation and reducing cable clutter. This feature allows the camera to receive both power and data through a single Ethernet cable, enabling more flexible placement options. The camera also includes an SD card slot for local storage, providing added redundancy and ensuring critical footage is retained even if network connectivity is lost.

Axis Communications places a strong emphasis on security, and the M1054 is no exception. It features robust security measures, including password protection, IP address filtering, and HTTPS encryption. These features provide a critical layer of defense against unauthorized access, ensuring that recorded video remains secure.

Moreover, the M1054 is compatible with Axis’ wide array of video management software and third-party systems, providing users the flexibility to integrate their surveillance solution into a broader security ecosystem. With its advanced features, reliable performance, and user-friendly design, the Axis M1054 network camera represents an excellent choice for businesses looking to enhance their security measures and ensure peace of mind.