Axis Communications F44 Capture Mode, Image Appearance, Go to Setup Video & Audio Camera Settings

Page 19

AXIS F44 Main Unit

Video and Audio

Capture Mode

Capture mode defines the maximum resolution and maximum frame rate available in the Axis product. A capture mode with a large maximum resolution has a reduced maximum frame rate and vice versa.

The capture mode setting also affects the camera’s angle of view as the effective size of the image sensor differs between capture modes.

Capture mode is set the first time the product is accessed. Select the desired capture mode and click OK.

The capture mode setting reduces image flicker in fluorescent light environments as image data is sampled at a rate that matches the local power line frequency.

Capture mode is set the first time the product is accessed. Select the capture mode with the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product and click OK.

When using 50 Hz, the maximum frame rate is limited to 25 fps.

Note

Power line frequency is different in different geographic regions. In the Americas, 60 Hz is usually used; most other parts of the world use 50 Hz. Local variations may apply, always check with the local authorities.

Important

Changing capture mode when the product has been configured is not recommended as most other settings will be either removed or reset.

To change capture mode, follow these steps:

1.Go to Setup > Video & Audio > Camera Settings.

2.Select the new capture mode.

3.Click Save.

4.Review and reconfigure all settings, for example:

-Stream profiles

-Motion detection windows

-Privacy masks

-Image overlays

-Exposure zones

-White balance windows

-Action rules

-Settings in uploaded applications

Image Appearance

Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation. The value 0 gives a black and white image.

The image Brightness can be adjusted in the range 0–100, where a higher value produces a brighter image.

Increasing the Sharpness can increase bandwidth usage. A sharper image might increase image noise especially in low light conditions. A lower setting reduces image noise, but the whole image will appear less sharp.

The Contrast changes the relative difference between light and dark. It can be adjusted using the slidebar.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Axis F44 Main Unit Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis F44 Main Unit Table of ContentsConnectors Performance Considerations Power Connector Connectors and ButtonsNetwork Connector ConnectorLED Indicators Shorten Sensor Unit Cable Set the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Configure Capture ModeSet Power Line Frequency Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsControls on the Live View Manual TriggerAMC Audio Controls Axis Media Control viewer toolbarMedia Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductImage Video and AudioVideo Stream Pixel CounterClick Save to apply the new settings Camera Settings264 Go to Setup Video & Audio Camera Settings Capture ModeImage Appearance Set Shutter to Exposure SettingsWhite Balance Shutter & GainOverlay Privacy MaskQuad stream Stream ProfilesGo to Video & Audio Video Stream and select the Image tab Overlay ImageGo to Video & Audio Overlay Image Go to Events Action Rules Audio SettingsUse Overlay Text in an Action Rule Audio ModesAudio Output Audio InputAudio Clips Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsGo to Detectors Audio Detection Audio DetectionApplication Licenses Install ApplicationGo to Setup Applications ApplicationsAxis F44 Main Unit Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersActions Recipient Use with action Add RecipientsRecipient Types Go to Events Recipients and click AddGo to Events Schedules and click Add Set Up RecurrencesSet Up Email Recipients Create SchedulesGo to Recordings List RecordingsFind Recordings Play RecordingRecording List Export Video ClipTo play a recording, follow these steps Go to Recordings Continuous Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 Axis Internet Dynamic DNS ServiceAxis Video Hosting System Avhs Host Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM can be disabled under System Options Network UPnPTM QoS Quality of ServiceUPnPTM SD Card StorageRTP/H.264 BonjourTo add a network share Network ShareClick Unmount Card can now be removed Format SD CardPorts & Devices MaintenanceSupport Advanced Reset to Factory Default Settings Problems setting the IP address TroubleshootingUpgrade the Firmware Symptoms, Possible Causes and Remedial ActionsBasic Product cannot be accessed from a browserProduct is accessible locally but not externally Problems with streaming H.264Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsStorage and disk management problems Technical Specifications Compression Function/group Specifications VideoResolutions Image settingsInstallation aids General Casing Function/group Specifications Data streamingInstallation Maintenance Built-inConnectors Audio Output Audio InputPerformance Considerations M2.2

F44 specifications

Axis Communications has long been a leader in the field of network cameras, and its F44 series exemplifies this commitment to innovation and quality. The Axis F44 is designed primarily for surveillance and security applications across various environments. This camera's unique modular design allows for flexibility in installation, adapting to diverse user needs and specific site requirements.

One of the standout features of the Axis F44 is its dual-channel capability. This means it can support two separate camera heads, allowing users to monitor different areas simultaneously while using a single video management system. This flexibility not only saves costs in terms of installations but also maximizes coverage without needing multiple standalone cameras.

The F44 series is equipped with Axis's advanced Lightfinder technology. This feature ensures exceptional image quality even in low-light conditions, making it ideal for night surveillance. With its wide dynamic range (WDR), the F44 can capture details in complex lighting situations, such as brightly lit areas next to shadowed regions. The result is clear and balanced video footage, crucial for identifying potential threats or intruders.

Another highlight is the camera’s support for Axis Zipstream technology. This advanced compression algorithm optimizes bandwidth and storage usage without compromising video quality. By analyzing the scene and selectively compressing different regions of the video stream, Zipstream ensures essential details remain clear while reducing the overall file size. This is particularly beneficial for systems with limited bandwidth or storage resources.

The F44 also emphasizes user-friendly features, including remote configuration and management capabilities. This allows security personnel to make adjustments without being on site, saving both time and resources. Furthermore, the camera is built with an array of analytics tools that can be integrated into existing systems for enhanced functionality. These include motion detection, tampering alarm, and video analytics features which can be customized based on specific security needs.

In terms of construction, the Axis F44 series is robust and designed for durability. It is compliant with various weather-proofing standards, making it suitable for outdoor installations in various climatic conditions. The camera can also be outfitted with various lens options depending on the specific use case, further increasing its versatility.

In conclusion, the Axis F44 combines advanced imaging technologies, flexible installation options, and robust construction, making it an excellent choice for security professionals seeking reliable and high-performing surveillance solutions. Whether for urban or rural applications, the F44’s blend of features ensures it meets diverse surveillance requirements effectively.
Top Page Image Contents