Axis Communications F44 user manual Find Recordings, Play Recording, Go to Recordings List

Page 37

AXIS F44 Main Unit

Recordings

Recordings

The Axis product can be configured to record video continuously or according to an action rule:

•To start a continuous recording, see page 39.

•To set up action rules, see page 33.

•To access recordings, see Find Recordings on page 37.

•To play recordings, see Play Recording on page 37.

•To export a recording as a video clip, see Export Video Clip on page 38.

•To configure camera controlled storage, see Storage on page 49.

Find Recordings

Recordings stored on the SD card or network share can be accessed from the Recordings > List page. The page lists all recordings on the storage device and shows each recording’s start date and time, duration and the event that triggered the recording.

Note

The recording’s start date and time is set according to the Axis product’s date and time settings. If the Axis product is configured to use a time zone different from the local time zone, make sure to configure the Recording time filters according to the product’s time zone. Date and time settings are configured under System Options > Date & Time, see Date & Time on page 43.

To find a recording, follow these steps:

1.Go to Recordings > List.

2.To reduce the number of recordings displayed, select the desired options under Filter: Recording time — List recordings that started between the From and To times.

Event — List recordings that were triggered by a specific event. Select continuous to list continuous recordings. Storage — List recordings from a specific storage device.

Sort — Specify how recordings should be sorted in the list. Results — Specify the maximum number of recordings to display.

3.To apply the filters, click the Filter button. Some filters may take a long time to complete.

4.The recordings are displayed in the Recording list.

To play a recording, select the recording and click Play. See also Play Recording on page 37.

To view detailed information about a recording, select the recording and click Properties.

To export a recording or a part of a recording as a video clip, select the recording and click Export. See also Export Video Clip on page 38.

To remove a recording from the storage device, select the recording and click Remove.

Play Recording

Recordings on the SD card or network share can be played directly from the Axis product’s webpages.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Axis F44 Main Unit Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis F44 Main Unit Table of ContentsConnectors Performance Considerations Network Connector Connectors and ButtonsConnector Power ConnectorLED Indicators Shorten Sensor Unit Cable Access from a Browser Access the ProductAccess from the Internet Set the Root PasswordSet Power Line Frequency Configure Capture ModeLive View Click Use HttpsControls on the Live View Go to Setup EventsManual Trigger To show the manual trigger buttons in the Live ViewAMC Audio Controls Axis Media Control viewer toolbarMedia Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductVideo Stream Video and AudioPixel Counter ImageClick Save to apply the new settings Camera Settings264 Go to Setup Video & Audio Camera Settings Capture ModeImage Appearance White Balance Exposure SettingsShutter & Gain Set Shutter toQuad stream Privacy MaskStream Profiles OverlayGo to Video & Audio Video Stream and select the Image tab Overlay ImageGo to Video & Audio Overlay Image Use Overlay Text in an Action Rule Audio SettingsAudio Modes Go to Events Action RulesAudio Output Audio InputAudio Clips Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons For more information about I/O ports, see I/O Ports onCamera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsGo to Detectors Audio Detection Audio DetectionGo to Setup Applications Install ApplicationApplications Application LicensesAxis F44 Main Unit Events Set Up Action RulesTriggers Go to Events Action Rules and click AddActions Recipient Types Add RecipientsGo to Events Recipients and click Add Recipient Use with actionSet Up Email Recipients Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddFind Recordings RecordingsPlay Recording Go to Recordings ListRecording List Export Video ClipTo play a recording, follow these steps Go to Recordings Continuous Continuous RecordingLanguages Security System OptionsUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee Click Install certificate and upload the certificate Go to Setup System Options Security CertificatesDate & Time Audio SupportNetwork Basic TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 Axis Internet Dynamic DNS ServiceAxis Video Hosting System Avhs DNS Configuration Advanced TCP/IP SettingsNTP Configuration Host Name ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM can be disabled under System Options Network UPnPTM QoS Quality of ServiceUPnPTM RTP/H.264 StorageBonjour SD CardClick Unmount Card can now be removed Network ShareFormat SD Card To add a network sharePorts & Devices MaintenanceSupport Advanced Reset to Factory Default Settings Upgrade the Firmware TroubleshootingSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct is accessible locally but not externally Product cannot be accessed from a browserProblems with streaming H.264 BasicVideo and image problems, general Status and Network indicator LEDs are flashing red rapidlySetup Video & Audio Camera Settings SettingsStorage and disk management problems Technical Specifications Resolutions Function/group Specifications VideoImage settings CompressionInstallation Function/group Specifications Data streamingMaintenance Built-in Installation aids General CasingConnectors Audio Output Audio InputPerformance Considerations M2.2

F44 specifications

Axis Communications has long been a leader in the field of network cameras, and its F44 series exemplifies this commitment to innovation and quality. The Axis F44 is designed primarily for surveillance and security applications across various environments. This camera's unique modular design allows for flexibility in installation, adapting to diverse user needs and specific site requirements.

One of the standout features of the Axis F44 is its dual-channel capability. This means it can support two separate camera heads, allowing users to monitor different areas simultaneously while using a single video management system. This flexibility not only saves costs in terms of installations but also maximizes coverage without needing multiple standalone cameras.

The F44 series is equipped with Axis's advanced Lightfinder technology. This feature ensures exceptional image quality even in low-light conditions, making it ideal for night surveillance. With its wide dynamic range (WDR), the F44 can capture details in complex lighting situations, such as brightly lit areas next to shadowed regions. The result is clear and balanced video footage, crucial for identifying potential threats or intruders.

Another highlight is the camera’s support for Axis Zipstream technology. This advanced compression algorithm optimizes bandwidth and storage usage without compromising video quality. By analyzing the scene and selectively compressing different regions of the video stream, Zipstream ensures essential details remain clear while reducing the overall file size. This is particularly beneficial for systems with limited bandwidth or storage resources.

The F44 also emphasizes user-friendly features, including remote configuration and management capabilities. This allows security personnel to make adjustments without being on site, saving both time and resources. Furthermore, the camera is built with an array of analytics tools that can be integrated into existing systems for enhanced functionality. These include motion detection, tampering alarm, and video analytics features which can be customized based on specific security needs.

In terms of construction, the Axis F44 series is robust and designed for durability. It is compliant with various weather-proofing standards, making it suitable for outdoor installations in various climatic conditions. The camera can also be outfitted with various lens options depending on the specific use case, further increasing its versatility.

In conclusion, the Axis F44 combines advanced imaging technologies, flexible installation options, and robust construction, making it an excellent choice for security professionals seeking reliable and high-performing surveillance solutions. Whether for urban or rural applications, the F44’s blend of features ensures it meets diverse surveillance requirements effectively.
Top Page Image Contents