Axis Communications F44 user manual QoS Quality of Service, UPnPTM

Page 48

AXIS F44 Main Unit

System Options

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark different types of traffic.

Note

Live audio DSCP will be equal to live video DSCP if H.264 over RTSP is used.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 41. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 53.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

48

Image 48
Contents Axis F44 Main Unit About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis F44 Main UnitConnectors Performance Considerations Connectors and Buttons Network ConnectorConnector Power ConnectorLED Indicators Shorten Sensor Unit Cable Access the Product Access from a BrowserAccess from the Internet Set the Root PasswordConfigure Capture Mode Set Power Line FrequencyLive View Click Use HttpsGo to Setup Events Controls on the Live ViewManual Trigger To show the manual trigger buttons in the Live ViewAxis Media Control viewer toolbar AMC Audio ControlsHow to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupVideo and Audio Video StreamPixel Counter ImageCamera Settings Click Save to apply the new settings264 Capture Mode Go to Setup Video & Audio Camera SettingsImage Appearance Exposure Settings White BalanceShutter & Gain Set Shutter toPrivacy Mask Quad streamStream Profiles OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Video & Audio Overlay Image Audio Settings Use Overlay Text in an Action RuleAudio Modes Go to Events Action RulesAudio Input Audio OutputAudio Clips Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onDetectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAudio Detection Go to Detectors Audio DetectionInstall Application Go to Setup ApplicationsApplications Application LicensesAxis F44 Main Unit Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddActions Add Recipients Recipient TypesGo to Events Recipients and click Add Recipient Use with actionSet Up Recurrences Set Up Email RecipientsCreate Schedules Go to Events Schedules and click AddRecordings Find RecordingsPlay Recording Go to Recordings ListExport Video Clip Recording ListTo play a recording, follow these steps Continuous Recording Go to Recordings ContinuousLanguages System Options SecurityUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time Audio SupportBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4Axis Video Hosting System Avhs Advanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPQoS Quality of Service UPnPTM can be disabled under System Options Network UPnPTMUPnPTM Storage RTP/H.264Bonjour SD CardNetwork Share Click Unmount Card can now be removedFormat SD Card To add a network shareMaintenance Ports & DevicesSupport Advanced Reset to Factory Default Settings Troubleshooting Upgrade the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 BasicStatus and Network indicator LEDs are flashing red rapidly Video and image problems, generalSetup Video & Audio Camera Settings SettingsStorage and disk management problems Technical Specifications Function/group Specifications Video ResolutionsImage settings CompressionFunction/group Specifications Data streaming InstallationMaintenance Built-in Installation aids General CasingConnectors Audio Input Audio OutputPerformance Considerations M2.2

F44 specifications

Axis Communications has long been a leader in the field of network cameras, and its F44 series exemplifies this commitment to innovation and quality. The Axis F44 is designed primarily for surveillance and security applications across various environments. This camera's unique modular design allows for flexibility in installation, adapting to diverse user needs and specific site requirements.

One of the standout features of the Axis F44 is its dual-channel capability. This means it can support two separate camera heads, allowing users to monitor different areas simultaneously while using a single video management system. This flexibility not only saves costs in terms of installations but also maximizes coverage without needing multiple standalone cameras.

The F44 series is equipped with Axis's advanced Lightfinder technology. This feature ensures exceptional image quality even in low-light conditions, making it ideal for night surveillance. With its wide dynamic range (WDR), the F44 can capture details in complex lighting situations, such as brightly lit areas next to shadowed regions. The result is clear and balanced video footage, crucial for identifying potential threats or intruders.

Another highlight is the camera’s support for Axis Zipstream technology. This advanced compression algorithm optimizes bandwidth and storage usage without compromising video quality. By analyzing the scene and selectively compressing different regions of the video stream, Zipstream ensures essential details remain clear while reducing the overall file size. This is particularly beneficial for systems with limited bandwidth or storage resources.

The F44 also emphasizes user-friendly features, including remote configuration and management capabilities. This allows security personnel to make adjustments without being on site, saving both time and resources. Furthermore, the camera is built with an array of analytics tools that can be integrated into existing systems for enhanced functionality. These include motion detection, tampering alarm, and video analytics features which can be customized based on specific security needs.

In terms of construction, the Axis F44 series is robust and designed for durability. It is compliant with various weather-proofing standards, making it suitable for outdoor installations in various climatic conditions. The camera can also be outfitted with various lens options depending on the specific use case, further increasing its versatility.

In conclusion, the Axis F44 combines advanced imaging technologies, flexible installation options, and robust construction, making it an excellent choice for security professionals seeking reliable and high-performing surveillance solutions. Whether for urban or rural applications, the F44’s blend of features ensures it meets diverse surveillance requirements effectively.