Panasonic GP-US932CU, GP-US932CUE, GP-US932CUS, GP-US932CUSE Precautions

Page 6

Precautions

Do not attempt to disassemble this product.

To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside.

Ask a qualified service person for servicing.

Handle this product with care.

Do not abuse the product. Avoid striking, shaking, etc. The product could be damaged by improper handling or stor- age.

Cleaning this product body

Turn the power off when cleaning the product. Use a dry cloth to clean the product.

Do not use strong abrasive detergent when cleaning the product. When the dirt is hard to remove, use a mild deter- gent and wipe gently. Then, wipe off the remaining deter- gent with a dry cloth.

Otherwise, it may cause discoloration. When using a chemi- cal cloth for cleaning, read the caution provided with the chemical cloth product.

Do not expose this product to rain or moisture, or try to operate it in wet areas.

Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the product, and also create the danger of electric shock.

Use this product for indoor use only.

Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air condition- er. Otherwise, it may cause deformation, discoloration and malfunction. Keep the product away from water.

Do not drop anything inside this product.

Dropping a metal part or other materials inside the product could permanently damage the product.

Do not operate this product beyond the specified tem- perature, humidity, or power source ratings.

Use the product under conditions where temperature is between 0°C and +40°C {32°F and 104°F}, and humidity is below 90 %. The input power resource is 12 V DC.

Clean the faceplate with care.

Do not clean the faceplate with strong or abrasive deter- gents. Use lens tissue or a cotton tipped applicator and ethanol.

Discoloration on the CCD color filter

When continuously shooting a bright light source such as a spotlight, the color filter of the CCD may have deteriorated and it may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spot- light for a certain period, the discoloration may remain.

Do not aim the camera head at strong light sources.

A light source such as a spot light causes a blooming (light bleeding) or a smear (vertical lines).

Smear

 

Bright subject

 

 

 

 

 

 

Blooming

Installing place

Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment.

Make sure that the installation area is strong enough to hold the product, such as a concrete ceiling. When the installa- tion area is not strong enough, reinforce and strengthen it.

Avoid installing in the following locations.

Locations where it may get wet from rain or water splash

Locations where a chemical agent is used such as a swimming pool (not only outdoor)

Locations subject to steam and oil smoke such as a kitchen

Locations near flammable gas or vapor

Locations where radiation or x-ray emissions are pro- duced

Locations subject to strong magnetic field or radio waves

Locations where corrosive gas is produced

Locations where it may be damaged by briny air such as seashores

Locations where the temperature is not between 0°C and +40°C {32°F and 104°F}.

Locations subject to vibrations (the product is not designed for on-vehicle use.)

Locations subject to condensation as the result of severe changes in temperature

6

Image 6
Contents Operating Instructions Risk of Electric Shock Do not Open Important Safety Instructions Contents Disclaimer of Warranty Limitation of LiabilityPrecautions Otherwise, lifetime of the internal parts may be shortened Preface Trademarks and Registered TrademarksCamera control unit CCU Major Operating Controls and Their FunctionsCamera head FrontUp/down/left/right buttons 2Camera cable connectorSelection button SEL 0Color bar display/AWC button BAR/AWCRear @1RGB/YPbPr connector RGB/YPbPr DC power connector DC 12V@0S-video output connector S-VIDEO 9RS-232C port RS-232CInstallation/Connection Sample of camera mounting on ceilingHow to mount lens Setting Procedures Setup menuSetup items Description Basic operations Matrix Electric Zoom FreezeCamera title setting Camera ID Character entryELC setting ELC Manual setup of detection areaElectronic sensitivity enhancement setting Sens UP Electronic shutter setting ShutterGain adjustment Gain Output signal setting Output SELRED DTL Adjusts the enhancement of red edge Scene file setting Scene FileDTL Mode Specifies the details Gamma Performs gamma adjustmentMatrix Adjusts the hue Knee Adjusts the knee pointWhite Clip Adjusts the white clip level Black Stretch Toggles the black stretch function on and offWhen the color axis is unclear Chroma Gain Adjusts chroma gainTotal PED Adjusts the pedestal level Color matrix splitting chartWhite balance setting White BAL Black balance setting Black BALDefault setting restoring Synchronization setting SyncElectronic zoom setting Electric Zoom Image freezing FreezeSEL Menu How to display or operate the SEL menuHow to assign settings Button assignmentTroubleshooting SymptomSymptom Specifications GP-US932CU/GP-US932CUSGP-US932CUE/GP-US932CUSE Standard Accessories Optional AccessoriesPage Panasonic Canada Inc Panasonic System Solutions CompanyFor business users in the European Union Panasonic Sales Company