Axis Communications 211W manual Unit connectors, Function, Specifications

Page 16
Terminal connector. Note that the pins are numbered 1-4, right to left.

Page 16

AXIS 211W Installation Guide

Unit connectors

Antenna connector - Reverse SMA connector for antenna.

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using shielded cables is recommended.

Power connector - Mini DC connector. 7 - 20V DC, max 5W. See product label for ± connection.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo connector must be used for the audio out.

I/O terminal connector - Used in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. It provides the interface to:

1 transistor output - For connecting external devices such as relays and LEDs. Connected devices can be activated by AXIS VAPIX AP, output buttons on the Live View page or by an Event Type. The output will show as active (shown under Event Configuration > Port Status) if the alarm device is activated.

Pin 4

Pin 2

Pin 3

Pin 1

1 digital input - An alarm input for connect-

ing devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under Event Configura- tion > Port Status).

Auxiliary power and GND

Function

Pin number

Notes

Specifications

 

 

 

 

GND

1

Ground

 

 

 

 

 

5VDC Power

2

Can be used to power auxiliary equipment

Max load = 100mA

 

 

(7-20VDC) or as a +5VDC (100mA) output.

 

 

 

 

 

Digital Input

3

Connect to GND to activate, or leave float-

Must not be exposed to

 

 

ing (or unconnected) to deactivate.

voltages greater than

 

 

 

20VDC

 

 

 

 

Transistor

4

Connects to GND when activated. If used

Max load = 100mA

Output

 

with an external relay, a diode must be con-

Max voltage = 24VDC

 

 

nected in parallel with the load for protec-

(to the transistor)

 

 

tion against voltage transients.

 

 

 

 

 

Image 16
Contents Axis 211W Page Installation steps Package contentsHardware overview DimensionsUnderside Rear panel Install the hardware Connect the cables and antennaAssign an IP address Method Recommended forAutomatic discovery Axis IP Utility single camera/small installationAssign the IP address manually optional Assign an IP address in a single device Axis Camera Management multiple cameras/large installationsAssign IP addresses in multiple devices Set the password Configure the wireless connection using a network cable Status of Wireless NetworksSecurity Wireless SettingsWPA-/WPA2-Enterprise EAP-TLS EAP-PEAP/MSCHAPv2Complete the wireless installation using a network cable Adjust the image and focus Accessing the Axis 211W from the InternetOther methods of setting the IP address Set the IP address with ARP/PingSpecifications Unit connectorsFunction Connection diagram LED indicatorsColor Indication Further information Resetting to the Factory Default SettingsTip Contenu de lemballage Étapes de linstallationArticle Modèles/variantes/remarques Présentation du matériel Vue de dessous Face arrièreInstallation du matériel Connexion des câbles et de lantenneMéthode Recommandée pour Système Dexploitation Attribution dune adresse IPDétection automatique Axis IP Utility Une seule caméra/petite installationDéfinissez manuellement ladresse IP optionnel Attribuer une adresse IP à un seul dispositif Attribuer des adresses IP à plusieurs dispositifszDéfinition du mot de passe État des réseaux sans fil Paramètres sans fil SécuritéAuthentification sélectionnez Fin de linstallation sans fil à laide dun câble réseau Débranchez le câble réseau de la caméraRéglage de limage et de la mise au point Accès à lappareil Axis 211W à partir dInternetAutres méthodes de définition de ladresse IP Définition de ladresse IP à laide dARP/PingConnecteurs de lunité Fonction Numéro Remarques Spécifications De brocheTémoins DEL Diagramme de connexionCouleur Indication Plus dinformations Rétablissement des paramètres dusine par défautConseil Lieferumfang InstallationsschritteKomponente Modelle/Varianten/Anmerkungen Unterseite Rückseite HardwareübersichtAbmessungen Hardware installieren Kabel und Antenne anschließenIP-Adresse festlegen Methode Empfohlen für BetriebssystemAutomatische Erkennung Axis IP Utility Einzelne Kamera/kleine InstallationIP-Adresse manuell zuweisen optional IP-Adressen mehreren Geräten zuweisen Axis Camera Management Mehrere Kameras/große InstallationEine IP-Adresse einem einzelnen Gerät zuweisen Kennwort festlegen Configuration Wireless Status der DrahtlosnetzwerkeDrahtloseinstellungen SicherheitWEP Axis 211W Installationsanleitung Bild und Fokus einstellen Internetzugriff auf die Axis 211WWeitere Methoden zum Festlegen der IP-Adresse IP-Adresse per ARP/Ping festlegenKameraanschlüsse Funktion Pinnummer Hinweise Technische DatenAnschlussschaltbild LED-AnzeigenFarbe Bedeutung Weitere Informationen Auf werkseitige Voreinstellungen zurücksetzenTipp Procedura di installazione Contenuto della confezioneImportante Articolo Modello/varianti/notePanoramica dellhardware DimensioniEtichetta lato inferiore Installazione dellhardware Collegamento dei cavi e dellantennaImpostazione di un indirizzo IP Metodo Consigliato per…Rilevamento automatico Axis IP Utility videocamera singola/piccole installazioniAssegnazione manuale dellindirizzo IP facoltativo Axis Camera Management più videocamere/grandi installazioni Assegnazione di un indirizzo IP in una singola videocameraAssegnazione degli indirizzi IP in più videocamere Selezionare Assign the following IP addressImpostazione della password Stato delle reti wireless Impostazioni wireless ProtezioneEapol version Versione Guida allinstallazione di Axis 211W Accesso al dispositivo Axis 211W da Internet Regolamento dellimmagine e della messa a fuocoAltri metodi di impostazione dellindirizzo IP Impostazione dellindirizzo IP con ARP/PingSistema operativo UPnP Pagine diConnettori Funzione Numero Specifiche PinSchema delle connessioni Indicatori LEDColore Indicazione Ulteriori informazioni Ripristino delle impostazioni di fabbricaSuggerimento Contenido del paquete Pasos de instalaciónArtículo Modelos/variantes/notas Dimensiones Presentación del hardwarePanel posterior Parte inferiorInstalación del hardware Conexión de los cables y la antenaConfiguración de una dirección IP Método Recomendado paraDetección automática Asignación manual de la dirección IP opcionalAsignación de direcciones IP en varios dispositivos Asignación de una dirección IP en un dispositivo individualSeleccione Assign the following IP address Configuración de la contraseña Configuración de la conexión inalámbrica con un cable de red Estado de las redes inalámbricasValores inalámbricos SeguridadEAP-TLS Eapol version VersiónFinalización de la conexión inalámbrica con un cable de red Ajuste de la imagen y el enfoque Acceso a la Axis 211W desde InternetOtros métodos para configurar la dirección IP Configuración de la dirección IP con ARP/PingConectores Función Número de Notas Especificaciones PinIndicadores LED Diagrama de conexionesColor Indicación Más información Restablecimiento de los valores inicialesSugerencia Page Axis 211W Installation Guide

211W specifications

Axis Communications, a pioneer in network video surveillance, has consistently delivered high-performance products that cater to a range of security needs. Among its notable offerings is the Axis 211W, a network camera designed for versatility and ease of use, making it an ideal choice for various surveillance applications.

One of the standout features of the Axis 211W is its exceptional image quality. This camera supports resolutions up to 640x480 pixels, ensuring clear and detailed video footage. The camera employs progressive scan technology, which provides smoother images of moving objects compared to traditional interlaced scanning. This capability is essential for monitoring dynamic environments, such as retail spaces or busy public areas.

The Axis 211W is equipped with a built-in microphone, allowing for audio surveillance along with video monitoring. This feature enhances situational awareness and can provide crucial evidence in security incidents. Additionally, the camera supports two-way audio, enabling users to communicate directly through the camera, a feature that can be particularly useful for remote engagement in security operations.

Another significant characteristic of the Axis 211W is its wireless capabilities. With built-in Wi-Fi support, it allows for flexible installation without the constraints of wired connections. This feature is beneficial in locations where running cables would be challenging or impractical. Furthermore, the camera adheres to the 802.11g wireless standard, ensuring stable connectivity for real-time monitoring.

The Axis 211W also comes equipped with advanced motion detection capabilities. Users can configure the camera to send alerts via email or trigger recording when movement is detected within its field of view. This feature helps in minimizing storage use while ensuring critical events are captured.

In terms of usability, the Axis 211W features a user-friendly web interface that simplifies the configuration and management of the camera. This allows for easy adjustment of settings, installation of firmware updates, and integration with various video management software solutions.

Overall, the Axis 211W embodies Axis Communications' commitment to quality, innovation, and security. With its combination of high-resolution imaging, audio capabilities, wireless flexibility, and intelligent features, this network camera represents a robust solution for anyone looking to enhance their security infrastructure. Whether for home use or in commercial environments, the Axis 211W stands out as a reliable tool for effective surveillance.