3Com FlexWATCH 3110 user manual 1 FW-3110 Hardware Description

Page 17

Network Video Server

User’s Manual

3Hardware Description

•This chapter contains list of items to be prepared for the installation of FlexWATCHTM server.

•Please carefully read this chapter before the installation.

•Please prepare all the necessary items before start installation to prevent any possible malfunction or any other hazard can be happened during the installation.

3.1Caution and observance

•Keep the device in the clean and dried area where air ventilation is guaranteed. The device is not waterproof. The waterproof device or similar device must protect from any possible hazard by water or heavy moisture etc.

•Regulated power supply is prerequisite for stable and optimal operation of the device. Use only power supply (SMPS 12V 1.5Am) supplied with FlexWATCHTM server. Manufacturer shall not liable for any hazard or shock caused by use of any other power supply.

•To prevent risk of electric shock, do not remove system-case. No user serviceable parts inside. Any repair or modification for the product will be allowed to qualified service personal only

•Use the cable supplied with FlexWATCHTM server. If you need to connect FlexWATCHTM server to the other device (External Modem, PTZ device), power on the devices before connect to the FlexWATCHTM server.

3.2Hardware Description

3.2.1FW-3110 Hardware Description

Front Panel View

A B C D E

17	Seyeon Tech Co., Ltd

- INTPLUS [2005] -

Image 17

Contents Version .0Rev0 User’s GuideNetwork Video Server User’s Manual Table of Contents Network Configuration External Device connection & configuration Utilities 100 Copyright Important Information Packing List Overview of FlexWATCHTM ServerSelf contained stable system What is FlexWATCHTM?Key Function of FlexWATCHTM Others Product SpecificationStatic IP address from Cable modem or xDSL line Basic Network Connection DiagramLeased Line connection Network Video Server User’s Manual Dial-in to FlexWATCHTM server through Pstn line ApplicationNetwork Video Server User’s Manual 1 FW-3110 Hardware Description Hardware DescriptionHardware Description LAN Port for 10/100M Base T Auto sensing DC 12V powerRear Panel View Key Words for Network IP assignmentNetwork Video Server User’s Manual IP address Static IP address enabled PC Dhcp Disabled PCCheck Points before IP assignment \ ping LAN cable or Cross-Over Cable Dhcp Enabled PCIP address Network Mask LAN Cable EnvironmentCross-over cable Through Installation Wizard Program Factory DefaultIP Assignment PC EnvironmentDescription of Window Menu Serial No. MAC Address IPInstallationWizard.exe is provide in the product CD‘Go to Home Page’ Button ‘Save IP Address’ ButtonIP Assignment through Hyper Terminal mode Network Video Server User’s Manual Stop bits Flow control Network Video Server User’s Manual Bash# ifconfig ActiveX based simple view Viewing mode Operation System Web browserLive View Live view page guide Java Applet based live viewSequence Cam ControlFrame rate Display sizeCamera value string configuration Camera configurationFW-Voyager based view and recording Output controlVideo with channel name Default Video FormatImage encryption Camera configurationLimited to Channel installFull Large Normal SmallVideo Motion Detection Setting procedureNetwork Video Server User’s Manual Recording in the FW-Manager Date & Time in the server clock System InformationDate & Time Access Control and User registration Admin Password SetupDate & Time using NTP server Following features are provided by this modeLimited Access and User registration Full AccessSelective Access Full AccessFormula to calculate required Bandwidth Frame rate control352X 10KBps 800K bps 0M bps 704X 25KBps 2M bps 5M bps Tx Module RegistrationNVCP Network Video Server User’s Manual WAN network Global Static WAN NetworkGlobal Static How to access the server under Dhcp environment Network configurationStatic IP Dhcp ClientIP notification by E-mail service PPPoE Configuration Http port configuration Network port configurationVdcp Port configuration Nvcp -Tx PortApplication with Dial-out WAN Configuration and ApplicationExternal Modem connection Dial-up through Standard modem Dial Out configurationDefault Route Tel#, User ID and User passwordDial-Out through Media specific device PPP ClientDial-in Configuration Remote IP address Service PathLocal IP address How to use Aoip service Aoip SetupNVCP-TX Port Aoip configurationAoip Server IP Http Port Network Status Pin-Out Information Serial Ports Configuration GuideAvailable Devices Ports Connection for using two different devicesConsole Hyper Terminal Modem Voice Serial Input Serial Output NoneInterface combination Ports Connection ConsoleHyper Terminal cable connection Installation & Configuration of External DeviceSerial Input device Serial output device Serial Output ConfigurationUARTUniversal Asynchronous Receiver Transmitter device 2 X 10 device & Z256PTZ connection PTZ device connection and configurationSupported PTZPan/Tilt/Zoom Device list Kalatel RNK RNK-DOME Voice Kit Connection and configurationConnection in router or firewall etc UDP PortAlarm OutputRelay output device connection Alarm input device connectionOpto-coupled Sensor input Diagram Mail, FTP, Sensor notification, Alarm output device controlManual control of Alarm output device Alarm output device connectionAlarm output device through web browser Relay Output Circuit DiagramAlarm output device through Admin Automatic Control of Alarm Output deviceNetwork Video Server User’s Manual Steps to use Buffering service Buffering ServiceFollowing services can be done by image buffering services Alarm buffering serviceTotal Buffer size Total Pre-alarm Buffer sizePre-alarm Buffer size Pre alarm buffer sizeAlarm Buffering Service size Go to Buffering service mode Delay between pre-alarm imageBuffer calculator 23500 kbAlarm buffering service size 60% Service Condition Condition Setup Criteria Set up Condition SetupEvent Criteria SetupSchedule Camera Connected and Disconnected DI Close StateMotion Detection Smtp Service address Mail configurationMail function configuration Number of post-alarm images Authentication LoginNumber of Pre alarm images Mail condition set up FTP ConfigurationDirectory option Value FormatBase File name Directory option for Buffered FTPBase Directory Name Directory name Directory option for Periodic FTP Duration ServiceFlexwatch/server/ Sun Mon Tue Wed Thu Fri Sat File name Sequence ModuloOverwrite FTP service configurationBuffered FTP service Example Periodic FTP serviceAlarm Buffering Service Configuration Alarm Buffering ServicePlayback of Pre/post alarm Image Preview Single Images Sensor Notification serviceNetwork Video Server User’s Manual Power off Save ConfigurationReboot Description of files system System UpdateWeb Only Update All kernel, RAM disk, System, Web UpdateSystem and Web Update Sensor Device Driver Update ProcedurePTZ Device Driver 103 104 Warranty