Active Thermal Management manual Control panel, UVS-7111 Users Manual

Page 16

UVS-7111 User's Manual			Camera Main Page

Control panel

All camera/network server products using Pelco-D, Pelco-P, A-linking and UIC drivers can be controlled using the UVS-7111 Video server. For more information, please go to our website.

1. Camera direction: controls the direction of the camera (up, down, left, right, home position).

Direction control.

2. Camera speed: controls the rotation speed of the camera from "1" (lowest) to "7" (highest).

Rotation speed.

Speed	1	2	3	4	5	6	7
Angle/Sec.	3	20	40	60	80	100	120

Image 16

Contents Page Contents UVS-7111 Users ManualContent Network cable network setting pagePackage Contents 5. Warranty card/certificatePackaging Contents 2. 12V DC power cableSystem Requirements System RequirementsUVS-7111/7111P/7111W Video Server Introduction Features and AdvantagesIntroduction / Features and Advantages System Instructions Wiring of the product DC PowerSystem Instructions RS-485 connector Reset to factory settingsAudio/Video Output LAN SocketHardware Installation 1. Select the installed place4. Connect to the power source for your camera 6. Connect to the power sourceCamera Settings Camera Settings1. Start the machine 2. Find the camera SearchCamera Setting 5. ConfirmationMAC Factory default network identity of the machine FINDER software3. Enter the Virtual Server setting page Camera Setting from a RouterCamera Setting from a Router Change the Internet Explorer Setting Change the Internet Explorer SettingSteps 2. Key in the default username and password 3. Installation of Internet Explorer ad-hoc componentsEnter the Main Page 1. Open the IE browser and key in the IP address of the productClick Install 4. The security warning screen appears. Click InstallCamera main page and image Descriptions Camera Main PageCamera Main Page Control panel 3. Preset presets the rotation points for the camera 16 points 1. Click Set to enter the Preset Setting screen4. Click Update to exit 5. Select the number you need 3. Control the camera direction 2. Enter the name of the location5. AutoPan enables/disables AutoPan 4. Tour enables/disables the tour mode of the cameraThe rotation points of the camera must be set up in advance 7. Alert Message enables/disables the alert message display 6. Alert displays alert triggerEnable/ disable the alert message display Alert message display area Enable/ disable the alert message Save function9. Camera Position sets the position for display of the image 8. Language selects a UI language10. View Size selects the size of the image 11. Streaming sets the video stream protocol HTTP is recommended Refer to Setting/Basic Setting/Network/Streaming for more information13. REC executes the video recording function 14. Snapshot executes the snapshot function16. Audio On/Off turns on/off the pickup function 17. ANS Automatic Noise Suppression systemSystem Settings Basic SettingsBasic Setting System System info Basic Setting System System InfoBasic Setting Video/Image Basic Setting Video Image Video ImageBasic Setting Video / Image Video Image 3GPP Ex Nokia N71. Follow these steps to set up your 3G viewing function4. Enter the link name 6. Select OK to save the setting 7. Select this stream name to proceed with linking 9. Connecting8. Select “Yes” to connect 10. Loading the image 11. Video stream screenBasic Setting Video / Image Video Image Video Resolution Basic Setting Video / Image Video Image Video FormatThe product offers 4 image resolutions PAL/NTSC 1. D1 704x576 2. VGA Basic Setting Video / Image Video Image Frame per Second FPS Basic Setting Video / Image Video Image Video QualitySelect a FPS Select a video qualityBasic Setting Video Image OSD Basic Setting Video Image OSD Display ModeBasic Setting Video Image OSD Display Text Basic Setting Video Image OSD Display ColorBasic Setting Audio Audio sound setting Basic Setting Audio SoundBasic Setting Audio Audio Audio Raw Format Basic Setting PTZ PTZ Basic Setting PTZBasic Setting PTZ PTZ PTZ camera Port Setting Basic Setting PTZ PTZ Driver Manager Basic Setting PTZ PTZ Driver UploadBasic Setting PTZ Serial Port Setting Basic Setting PTZ Serial Port Setting Data bitsBasic Setting PTZ Serial Port Setting Parity Basic Setting PTZ Serial Port Setting Stop bitsyour cameras for the accurate figure Basic Setting UserUser Basic Setting User User List access privilege listBasic Setting User User Setting privilege setting Basic Setting Network Network setting Basic Setting Network Network cable network setting pageDHCP setting Other settingsBasic Setting Network Wireless wireless network setting page Basic Setting Network Wireless WirelessWireless network setting page Wireless networking modeMode Selection of the wireless networking mode Authentication Type Network authentication type1. Infrastructure Infrastructure networking mode 2. AdHoc Point-to-point networking modeWEP Encryption WEP encryption function SSID Service Set IdentifierEnter the name of the base station AP to which you want to connect Encoding ASCIIAvailable characters 0~9, a~f, A~FSelection Streaming port setting Basic Setting Network Streaming steaming setting1. HTTP 2. RTSP 3. RTP Basic Setting Network PPPoE PPPoE Basic Setting Network PPPoE dial-up networking settingBasic Setting Network PPPoE PPPoE Information Basic Setting Network DDNS Dynamic Domain Name Server Setting Item DescriptionBasic Setting Network UPnP Universal Plug and Play Basic Setting Network UPnP UPnP DeviceBasic Setting Network UPnP UPnP Traversal To activate the UPnP function in Windows OS3. View the connection device using My Network Places 2. Click Exceptions 3. Check UPnP Configuration2. Open Windows firewall option 1. Open My Network PlacesBasic Setting Network SMTP Server mail server setting Options Basic Setting Network SambaSamba setting IP address change notice Basic Setting Network Notification Of IP Address ChangeNotification setting Basic Setting Date/Time date/time setting Basic Setting Date/Time Server Time the date/time of the serverBasic Setting Date/Time PC Time the date/time of your PC Basic Setting Date/Time Time Setting date/time settingBasic Setting IP Filter Basic Setting IP Filter GeneralIP Filtering enables/disables the IP filter Basic Setting IP Filter Filter IP Address Overview of the set IPsApplication Setting Event event trigger setting page Application SettingApplication Setting Event Event List trigger event setting Basic Setting Add Event Add Event setting pageOptions Note You can only set one trigger event onceApplication Setting Event Trigger manual test of trigger response Trigger Alarm output Alarm outputTrigger LED LED indicator display Trigger mail Sending mailApplication Setting Event Event Servers setting for uploading trigger event file to the serverUVS-7111 Users ManualApplication Setting Application Setting Motion Detection Application Setting Firmware upgradeApplication Setting Important! Read Carefully4. Click Application Setting Factory Default Factory Default Reset to factory defaultResets all parameters, except the IP parameters Resets all parametersBackup Data backup Restore backup parametersBack all parameters File backupApplication Setting Reboot You can enable this function for the camera to reboot automaticallyAttachment A External Alarm Attachment A External AlarmAlarm Input #1 A. Max 24VDC, 12mA Alarm Input #1/2 K. GroundExternal Alarm I/O Circuit Diagram Attachment C Troubleshooting and FAQsmay bring about damage to the camera or product fatal electric shock Image Resolution Attachment B Bandwidth EstimationAttachment B Bandwidth Estimation Average range of Data SizesAnswer and Solution Camera InstallationQuestion FunctionAccess to Camera the current security setting Others