Active Thermal Management UVS-7111 manual Basic Setting Network SMTP Server mail server setting

Page 47

UVS-7111 User's Manual			Basic Setting

Basic Setting > Network > SMTP Server (mail server setting)

Thiscamera is able to transmit images to a particular email address when a motion detection event occurs or a sensor is triggered. To use this function, a mail server setting for the camera is required.

Enter the following information in sequential order to complete the setting:

・SMTP server: the SMTP server IP address.

・SMTP From: the email of the sender, i.e. xxx@xxx.com

・MTP Authentication: enables/disables

・User name: the SMTP server username.

・Password: the password of the SMTP server. ・Select “SAVE” to save the setting.

Image 47

Contents Page Network cable network setting page ContentsUVS-7111 Users Manual Content2. 12V DC power cable Package Contents5. Warranty card/certificate Packaging ContentsUVS-7111/7111P/7111W Video Server System RequirementsSystem Requirements Introduction / Features and Advantages Features and AdvantagesIntroduction System Instructions Wiring of the product DC PowerSystem Instructions LAN Socket RS-485 connectorReset to factory settings Audio/Video Output6. Connect to the power source Hardware Installation1. Select the installed place 4. Connect to the power source for your camera2. Find the camera Search Camera SettingsCamera Settings 1. Start the machineFINDER software Camera Setting5. Confirmation MAC Factory default network identity of the machineCamera Setting from a Router Camera Setting from a Router3. Enter the Virtual Server setting page Steps Change the Internet Explorer SettingChange the Internet Explorer Setting 1. Open the IE browser and key in the IP address of the product 2. Key in the default username and password3. Installation of Internet Explorer ad-hoc components Enter the Main PageCamera main page and image 4. The security warning screen appears. Click InstallClick Install Camera Main Page Camera Main PageDescriptions Control panel 3. Control the camera direction 2. Enter the name of the location 3. Preset presets the rotation points for the camera 16 points1. Click Set to enter the Preset Setting screen 4. Click Update to exit 5. Select the number you needThe rotation points of the camera must be set up in advance 4. Tour enables/disables the tour mode of the camera5. AutoPan enables/disables AutoPan Enable/ disable the alert message Save function 7. Alert Message enables/disables the alert message display6. Alert displays alert trigger Enable/ disable the alert message display Alert message display area10. View Size selects the size of the image 8. Language selects a UI language9. Camera Position sets the position for display of the image Refer to Setting/Basic Setting/Network/Streaming for more information 11. Streaming sets the video stream protocol HTTP is recommended14. Snapshot executes the snapshot function 13. REC executes the video recording function17. ANS Automatic Noise Suppression system 16. Audio On/Off turns on/off the pickup functionBasic Setting System System Info System SettingsBasic Settings Basic Setting System System infoEx Nokia N71. Follow these steps to set up your 3G viewing function Basic Setting Video/ImageBasic Setting Video Image Video Image Basic Setting Video / Image Video Image 3GPP11. Video stream screen 4. Enter the link name 6. Select OK to save the setting7. Select this stream name to proceed with linking 9. Connecting 8. Select “Yes” to connect 10. Loading the imageThe product offers 4 image resolutions PAL/NTSC 1. D1 704x576 2. VGA Basic Setting Video / Image Video Image Video FormatBasic Setting Video / Image Video Image Video Resolution Select a video quality Basic Setting Video / Image Video Image Frame per Second FPSBasic Setting Video / Image Video Image Video Quality Select a FPSBasic Setting Video Image OSD Display Color Basic Setting Video Image OSDBasic Setting Video Image OSD Display Mode Basic Setting Video Image OSD Display TextBasic Setting Audio Audio Audio Raw Format Basic Setting Audio SoundBasic Setting Audio Audio sound setting Basic Setting PTZ PTZ PTZ camera Port Setting Basic Setting PTZBasic Setting PTZ PTZ Basic Setting PTZ Serial Port Setting Data bits Basic Setting PTZ PTZ Driver ManagerBasic Setting PTZ PTZ Driver Upload Basic Setting PTZ Serial Port Settingyour cameras for the accurate figure Basic Setting PTZ Serial Port Setting Stop bitsBasic Setting PTZ Serial Port Setting Parity Basic Setting User User List access privilege list Basic Setting UserUserBasic Setting User User Setting privilege setting Other settings Basic Setting Network Network settingBasic Setting Network Network cable network setting page DHCP settingWireless networking mode Basic Setting Network Wireless wireless network setting pageBasic Setting Network Wireless Wireless Wireless network setting page2. AdHoc Point-to-point networking mode Mode Selection of the wireless networking modeAuthentication Type Network authentication type 1. Infrastructure Infrastructure networking modeEnter the name of the base station AP to which you want to connect SSID Service Set IdentifierWEP Encryption WEP encryption function 0~9, a~f, A~F EncodingASCII Available charactersSelection 1. HTTP 2. RTSP 3. RTP Basic Setting Network Streaming steaming settingStreaming port setting Basic Setting Network PPPoE PPPoE Information Basic Setting Network PPPoE dial-up networking settingBasic Setting Network PPPoE PPPoE Item Description Basic Setting Network DDNS Dynamic Domain Name Server SettingTo activate the UPnP function in Windows OS Basic Setting Network UPnP Universal Plug and PlayBasic Setting Network UPnP UPnP Device Basic Setting Network UPnP UPnP Traversal1. Open My Network Places 3. View the connection device using My Network Places2. Click Exceptions 3. Check UPnP Configuration 2. Open Windows firewall optionBasic Setting Network SMTP Server mail server setting Samba setting Basic Setting Network SambaOptions Notification setting Basic Setting Network Notification Of IP Address ChangeIP address change notice Basic Setting Date/Time Time Setting date/time setting Basic Setting Date/Time date/time settingBasic Setting Date/Time Server Time the date/time of the server Basic Setting Date/Time PC Time the date/time of your PCBasic Setting IP Filter Filter IP Address Overview of the set IPs Basic Setting IP FilterBasic Setting IP Filter General IP Filtering enables/disables the IP filterApplication Setting Event Event List trigger event setting Application SettingApplication Setting Event event trigger setting page Note You can only set one trigger event once Basic SettingAdd Event Add Event setting page OptionsTrigger mail Sending mail Application Setting Event Trigger manual test of trigger responseTrigger Alarm output Alarm output Trigger LED LED indicator displaysetting for uploading trigger event file to the server Application Setting Event Event ServersUVS-7111 Users ManualApplication Setting Important! Read Carefully Application Setting Motion DetectionApplication Setting Firmware upgrade Application Setting4. Click Resets all parameters Application Setting Factory DefaultFactory Default Reset to factory default Resets all parameters, except the IP parametersFile backup Backup Data backupRestore backup parameters Back all parametersYou can enable this function for the camera to reboot automatically Application Setting RebootAlarm Input #1/2 K. Ground Attachment A External AlarmAttachment A External Alarm Alarm Input #1 A. Max 24VDC, 12mAmay bring about damage to the camera or product fatal electric shock Attachment C Troubleshooting and FAQsExternal Alarm I/O Circuit Diagram Average range of Data Sizes Image ResolutionAttachment B Bandwidth Estimation Attachment B Bandwidth EstimationFunction Answer and SolutionCamera Installation QuestionAccess to Camera the current security setting Others