Active Thermal Management UVS-7111 manual Basic Setting Network Samba, Options, Samba setting

Page 48

UVS-7111 User's Manual			Basic Setting

Basic Setting > Network > Samba

This camera is able to upload the snapshots to a specified shared folder when an event is triggered. To use this function, a Samba setting is required.

Options:

Active:

Samba Authentication:

Username:

Password:

Path:

Shared Folder Size (MB):

Max Record File Size (MB):

Enable/Disable

Enable/Disable the username the password

specify the IP address of the computer you want to share with and the file name, i.e. 192.168.0.X/xxx

the total capacity of the folder. Always remember to set the size of the folder to avoid exhaustion of disk capacity.

the upper limit of the record file size. The size should not exceed the total capacity of the folder

Samba setting

Image 48

Contents Page Contents UVS-7111 Users ManualContent Network cable network setting pagePackage Contents 5. Warranty card/certificatePackaging Contents 2. 12V DC power cableSystem Requirements System RequirementsUVS-7111/7111P/7111W Video Server Features and Advantages IntroductionIntroduction / Features and Advantages Wiring of the product DC Power System InstructionsSystem Instructions RS-485 connector Reset to factory settingsAudio/Video Output LAN SocketHardware Installation 1. Select the installed place4. Connect to the power source for your camera 6. Connect to the power sourceCamera Settings Camera Settings1. Start the machine 2. Find the camera SearchCamera Setting 5. ConfirmationMAC Factory default network identity of the machine FINDER softwareCamera Setting from a Router 3. Enter the Virtual Server setting pageCamera Setting from a Router Change the Internet Explorer Setting Change the Internet Explorer SettingSteps 2. Key in the default username and password 3. Installation of Internet Explorer ad-hoc componentsEnter the Main Page 1. Open the IE browser and key in the IP address of the product4. The security warning screen appears. Click Install Click InstallCamera main page and image Camera Main Page DescriptionsCamera Main Page Control panel 3. Preset presets the rotation points for the camera 16 points 1. Click Set to enter the Preset Setting screen4. Click Update to exit 5. Select the number you need 3. Control the camera direction 2. Enter the name of the location4. Tour enables/disables the tour mode of the camera 5. AutoPan enables/disables AutoPanThe rotation points of the camera must be set up in advance 7. Alert Message enables/disables the alert message display 6. Alert displays alert triggerEnable/ disable the alert message display Alert message display area Enable/ disable the alert message Save function8. Language selects a UI language 9. Camera Position sets the position for display of the image10. View Size selects the size of the image 11. Streaming sets the video stream protocol HTTP is recommended Refer to Setting/Basic Setting/Network/Streaming for more information13. REC executes the video recording function 14. Snapshot executes the snapshot function16. Audio On/Off turns on/off the pickup function 17. ANS Automatic Noise Suppression systemSystem Settings Basic SettingsBasic Setting System System info Basic Setting System System InfoBasic Setting Video/Image Basic Setting Video Image Video ImageBasic Setting Video / Image Video Image 3GPP Ex Nokia N71. Follow these steps to set up your 3G viewing function4. Enter the link name 6. Select OK to save the setting 7. Select this stream name to proceed with linking 9. Connecting8. Select “Yes” to connect 10. Loading the image 11. Video stream screenBasic Setting Video / Image Video Image Video Format Basic Setting Video / Image Video Image Video ResolutionThe product offers 4 image resolutions PAL/NTSC 1. D1 704x576 2. VGA Basic Setting Video / Image Video Image Frame per Second FPS Basic Setting Video / Image Video Image Video QualitySelect a FPS Select a video qualityBasic Setting Video Image OSD Basic Setting Video Image OSD Display ModeBasic Setting Video Image OSD Display Text Basic Setting Video Image OSD Display ColorBasic Setting Audio Sound Basic Setting Audio Audio sound settingBasic Setting Audio Audio Audio Raw Format Basic Setting PTZ Basic Setting PTZ PTZBasic Setting PTZ PTZ PTZ camera Port Setting Basic Setting PTZ PTZ Driver Manager Basic Setting PTZ PTZ Driver UploadBasic Setting PTZ Serial Port Setting Basic Setting PTZ Serial Port Setting Data bitsBasic Setting PTZ Serial Port Setting Stop bits Basic Setting PTZ Serial Port Setting Parityyour cameras for the accurate figure Basic Setting UserUser Basic Setting User User List access privilege listBasic Setting User User Setting privilege setting Basic Setting Network Network setting Basic Setting Network Network cable network setting pageDHCP setting Other settingsBasic Setting Network Wireless wireless network setting page Basic Setting Network Wireless WirelessWireless network setting page Wireless networking modeMode Selection of the wireless networking mode Authentication Type Network authentication type1. Infrastructure Infrastructure networking mode 2. AdHoc Point-to-point networking modeSSID Service Set Identifier WEP Encryption WEP encryption functionEnter the name of the base station AP to which you want to connect Encoding ASCIIAvailable characters 0~9, a~f, A~FSelection Basic Setting Network Streaming steaming setting Streaming port setting1. HTTP 2. RTSP 3. RTP Basic Setting Network PPPoE dial-up networking setting Basic Setting Network PPPoE PPPoEBasic Setting Network PPPoE PPPoE Information Basic Setting Network DDNS Dynamic Domain Name Server Setting Item DescriptionBasic Setting Network UPnP Universal Plug and Play Basic Setting Network UPnP UPnP DeviceBasic Setting Network UPnP UPnP Traversal To activate the UPnP function in Windows OS3. View the connection device using My Network Places 2. Click Exceptions 3. Check UPnP Configuration2. Open Windows firewall option 1. Open My Network PlacesBasic Setting Network SMTP Server mail server setting Basic Setting Network Samba OptionsSamba setting Basic Setting Network Notification Of IP Address Change IP address change noticeNotification setting Basic Setting Date/Time date/time setting Basic Setting Date/Time Server Time the date/time of the serverBasic Setting Date/Time PC Time the date/time of your PC Basic Setting Date/Time Time Setting date/time settingBasic Setting IP Filter Basic Setting IP Filter GeneralIP Filtering enables/disables the IP filter Basic Setting IP Filter Filter IP Address Overview of the set IPsApplication Setting Application Setting Event event trigger setting pageApplication Setting Event Event List trigger event setting Basic Setting Add Event Add Event setting pageOptions Note You can only set one trigger event onceApplication Setting Event Trigger manual test of trigger response Trigger Alarm output Alarm outputTrigger LED LED indicator display Trigger mail Sending mailApplication Setting Event Event Servers setting for uploading trigger event file to the serverUVS-7111 Users ManualApplication Setting Application Setting Motion Detection Application Setting Firmware upgradeApplication Setting Important! Read Carefully4. Click Application Setting Factory Default Factory Default Reset to factory defaultResets all parameters, except the IP parameters Resets all parametersBackup Data backup Restore backup parametersBack all parameters File backupApplication Setting Reboot You can enable this function for the camera to reboot automaticallyAttachment A External Alarm Attachment A External AlarmAlarm Input #1 A. Max 24VDC, 12mA Alarm Input #1/2 K. GroundAttachment C Troubleshooting and FAQs External Alarm I/O Circuit Diagrammay bring about damage to the camera or product fatal electric shock Image Resolution Attachment B Bandwidth EstimationAttachment B Bandwidth Estimation Average range of Data SizesAnswer and Solution Camera InstallationQuestion FunctionAccess to Camera the current security setting Others