Kenwood TS-570D Sending Messages, Changing Inter-message Interval, Changing Volume

Page 60

12 OPERATOR CONVENIENCES

■Sending Messages

1 Select SSB, FM, or AM.

•Use the same mode for transmitting and receiving.

2Press [VOX] to switch VOX ON or OFF.

•Depending on this selection, the subsequent procedures differ.

3If you switch OFF VOX in step 2, press [SEND], or press and hold Mic [PTT].

4Press [CH 1], [CH 2], or [CH 3], depending on which channel you want to use.

•For example, “AP 1– –” appears while playing back the message in channel 1.

•To interrupt playback, press [CLR].

5To play back another message in sequence, press the corresponding [CH 1], [CH 2], or [CH3] while playing back the first message.

•Up to three channels can be queued at the same time.

6If you press [SEND] or Mic [PTT] in step 3, press [SEND] again or release Mic [PTT].

■Changing Inter-message Interval

For repetitive message playback, you can change the interval between each series of messages. Use Menu No. 24, and select the time in the range of 0 to 60 seconds.

■Changing Volume

Turning the AF control does not change the volume for playback. To change the volume, use Menu No.25.

54

Image 60

Contents TS-570S Supplied Accessories Accessory Part NumberApplicable Model Intelligent Digital Enhanced Communications SystemFeatures Writing Conventions FollowedKEY2 Contents Memory Features Specifications Appendix COM Connector Protocol IndexScan Operator ConveniencesPower Source Power Cable ProtectionPower Lines CleaningInstallation Antenna ConnectionTransmission Line MHz 14 MHz 30 MHz DC Power Supply Connection InstallationGround Connection Lightning ProtectionAccessory Connections Front PanelRear Panel Your First QSO DSP Slope High control Fully clockwise DSP Slope LOW controlYour Getting Acquainted Front PanelGetting Acquainted UP/DOWN buttons Split buttonTF-SET button Clear buttonMicrophone Rear Panel GND postKEY and Paddle jacks EXT SP jackDisplay @6M.SCR @7LSB@8USB #1FSKSwitching Power ON/OFF Adjusting VolumeOperating Basics Selecting VFO a or VFO BSelecting a Mode Adjusting SquelchSelecting a Frequency Front Panel MeterSelecting Transmit Power TransmittingMicrophone Gain Menu Setup What is a MENU?Menu Access Menu A/ Menu BMenu Configuration Menu SetupFunction Selections Default GroupSetting Transfer Rate bps Stop Bits SplitCross Reference for Menu Functions Basic Communicating SSB TransmissionCW Transmission Basic CommunicatingAuto ZERO-BEAT TX SIDETONE/ RX Pitch FrequencyFM Transmission AM TransmissionTX Deviation Selection Press FilterSpecialized Communicating SPLIT-FREQUENCY OperationTF-SET Transmit Frequency SET UP/DWNFM Repeater Operation Specialized CommunicatingArrl 10-METER Band Plan Mode/ActivityFM Ctcss Operation Specialized Communicating Selecting Subtone FrequencyContinuous or Burst SUBTONES? Digital Operation Rtty Frequency Shift KeyingRtty Frequencies Iaru Region A./CanadaPacket Frequencies Slow Scan TV/ Facsimile Satellite OperationSstv Frequencies Communicating Aids ReceivingSelecting Your Frequency RIT Receive Incremental Tuning Communicating AidsAGC Automatic Gain Control RX EqualizerDelay Time Press DelayVOX VOICE-OPERATED Transmit Microphone Input LevelXIT Transmit Incremental Tuning Communicating Aids Speech ProcessorMonitoring Transmitted Signals Transmit InhibitChanging Frequency While Transmitting Changing Transmit Bandwidth SSB/AMUsing Semi BREAK-IN or Full BREAK-IN Auto WeightingCW BREAK-IN Electronic KeyerCommunicating Aids Changing LOCKED-WEIGHT BUG KEY FunctionCW Message Memory Rejecting Interference If FilterNoise Blanker Changing if Filter BandwidthAttenuator PreamplifierDSP Tools Rejecting InterferenceBeat Cancel Setting NR2 Time ConstantNoise Reduction CW/ FSK ModesMemory Features Conventional MemoryStoring Data in Memory Simplex ChannelsMemory Features Split-Frequency ChannelsMemory Recall Memory Recall and ScrollMemory Scroll Temporary Frequency ChangesMemory-VFO Split Operation To use a memory channel for receivingMemory Features Memory Transfer Memory VFO TransferChannel Channel Transfer Memory Features Storing Frequency Ranges Full ResetErasing Memory Channels Confirming Start/End FrequenciesQuick Memory Storing Into Quick MemoryMemory Channel Lockout Press CLRMemory Features Recalling Quick Memory Temporary Frequency ChangesQuick Memory VFO Transfer Scan Program ScanScan Hold Scan Type PurposeMemory Scan ScanALL-CHANNEL Scan Group ScanMicroprocessor Reset Switching ANT 1/ ANTOperator Conveniences Frequency Lock FunctionBeep Function Display DimmerProgram Function Button Operator ConveniencesSetting UP Using Quick TransferQuick Data Transfer Using a Transverter Menu Setting Transfer Rate Stop BitsComputer Control Communication ParametersPresetting Automatic Antenna TunerAttune again Recording Messages Message PlaybackChecking Messages Changing Volume Sending MessagesChanging Inter-message Interval New Mode Announcement MenuVoice StepsOptional Accessories DRU-3APC-1A PG-2ZInstalling Options Removing the Bottom CaseDRU-3A Digital Recording Unit Installing Options VS-3 Voice Synthesizer UnitFilters SO-2 TEMPERATURE-COMPENSATED Crystal Oscillator Tcxo Connecting Peripheral Equipment ComputerCompatible Transceiver Pin No. Pin NameConnecting Peripheral Equipment Rtty EquipmentLinear Amplifier Antenna TunerMCP and TNC Pin No FunctionMaintenance ServiceService Note CleaningInternal Adjustments MaintenanceAccessing the Internal Fuse Reference Frequency CalibrationTroubleshooting Problem Probable Cause Corrective ActionFollowed DSP Slope LOW control orChanging Receive Press LSB/USB, CW/FSK, orPress LSB/USB or FM/AM to Repeater Operation TS-570S TS-570D SSB, CWFSK, FM Specifications SSB, CW, FSKHardware Description Control OperationAppendix COMComputer Control Commands Alphabetical CommandsError Messages ParametersAlphabetical Command Table OFF/ONParameter Table FormatMenu Selection Table for EX Command UP/DOWNComputer Control Command Tables I o !0DN UP DOWN/UP LK Frequency Lock MG MIC Gain RT RIT RX TX RX, TX VOX Function VFO Sstv