Kenwood TS-570D instruction manual Parameter Table, Format

APPENDIX ●

■Parameter Table

Format	Name	No. of		Format
No.		Digits
1	SW	1	0: OFF		1: ON
			0: No selection		5: AM
			1: LSB		6: FSK
2	MODE	1	2: USB		7: CW-R
			3: CW		8: No selection
			4: FM		9: FSK-R
			0: VFO A
3	FUNCTION	1	1: VFO B
			2: Memory
			Represented in Hz.
4	FREQUENCY	11	Ex.: 00014230000 is
			14.230 MHz
			The first digit is “+” or “–”,
5	RIT/XIT	5	and the remaining four digits
	FREQUENCY		indicate the frequency in Hz.
			Ex.: +5320 is +5.32 kHz
7	MEMORY	2	Represented using 00~99.
	CHANNEL
	MEMORY		0: Receive	(Start freq.)
9	CHANNEL	1	1: Transmit	(End freq.)
	SPLIT DATA		(Start/End freq.: Ch.90~99)
10	MEMORY	1	0: Not locked out
	LOCKOUT		1: Locked out
11	TX/RX	1	0: Receive
			1: Transmit
	TONE		Represents the tone number
14		2	(01~39). See the subtone
	NUMBER
			frequency table on page 25.
			Represents the type of
16	MODEL	3	transceiver.
	NUMBER		TS-570S: 018
			TS-570D: 017
	METER		RM command: 0000~0008
22		4	SM command: 0000~0015
	VALUE
			Relative values are output.
			0: No selection
24	METER	1	1: SWR
	SWITCH		2: COMP
			3: ALC
			0: No playback
			A Set command cancels
27	PLAYBACK	1	playback.
	CHANNEL		1: Channel 1
			2: Channel 2
			3: Channel 3
30	ANTENNA	1	0: Antenna tuner thru
	TUNER		1: Antenna tuner in-line
			Represented using
31	GAIN	3	000 (min.)~255 (max.).
			MG command: 000~100
			0: AI OFF
			1: IF command outputs its
			Answer command
32	AI NUMBER	1	periodically.
			2: For parameter changes,
			the corresponding Answer
			command is output.
			3: Both 1 and		2.
33	ANTENNA	1	1: ANT 1
	NUMBER		2: ANT 2

Format		No.
	Name	of		Format
No.
		Digits
35	MENU	3	Represented using 000~051.
	NUMBER
36	MENU	4	See table on page 74.
	SELECTION
38	FILTER	4	Represented using
	WIDTH		0000~9999.
39	AGC TIME	3	002: Fast
	CONSTANT		004: Slow
	IF SHIFT		“+”: Upward freq. shift
40		1	(or “	”)
	DIRECTION
			“–”: Downward freq. shift
41	IF SHIFT	4	Represented in Hz using
	FREQUENCY		0000~1100.
	KEYER		Represented in words per
42		3	minute using 010 (min.)~
	SPEED
			060 (max.).
43	KEYER	24	Contains the CW message.
	MESSAGE
44	KEYER	1	0: Buffer space available
	BUFFER		1: Buffer space not available
			0: Not recording. A Set
			command cancels
45	LOAD	1	recording.
	MESSAGE		1: Channel 1
			2: Channel 2
			3: Channel 3
46	LEVEL	3	Represented using
			000 (min.)~255 (max.).
47	POWER	3	Represented in watts using
	CONTROL		005~100, 5 W steps.
	SEMI		Represented in msec using
49	BREAK-IN	4
			0000~1000, 50 ms steps.
	DELAY TIME
			1: Partial Reset
50	SYSTEM	1	([A/B]+[			])
	RESET		2: Full Reset
			([A=B]+[		])
51	VOX DELAY	4	Represented in msec using
	TIME		0000~3000.
	CW RX		Represented using
52		2	00 (400 Hz min.) ~
	PITCH
			12 (1000 Hz max.).
			Represented using 00~20
			High cut-off
53	DSP SLOPE	2	00: 5.0 kHz 20: 1.0 kHz
			Low cut-off
			00: 10 Hz			20: 1000 Hz
54	VOX GAIN	3	Represented using
			001 (min.) ~ 009 (max.).
55	VOICE	1	1: Voice 1			2: Voice 2
	RECALL
	NOISE		0: Noise Reduction OFF
56		1	1: Noise Reduction 1
	REDUCTION
			2: Noise Reduction 2
			0: Beat Cancel OFF
57	BEAT	1	1: Beat Cancel ON
	CANCEL		2: Enhanced Beat Cancel
			ON

73