Kenwood TS-570D instruction manual New Mode Announcement, Menu, Voice, Steps

Page 61

12 OPERATOR CONVENIENCES

VS-3 VOICE SYNTHESIZER (OPTIONAL)

Install the optional VS-3 unit to use this function. Each time you change the transceiver mode such as VFO A/B or Memory Recall, the transceiver automatically announces the new mode. In addition, you can program the front panel [PF] button so that pressing [PF] makes the transceiver announce the displayed information. If you have the optional MC-47 microphone, you can program one of the Mic [PF] buttons for this function.

For an explanation on how to install the VS-3 unit, refer to “INSTALLING OPTIONS” {page 57}.

The table below shows what the transceiver automatically announces when it enters a new mode.

Key Pressed

New Mode

Announcement

 

 

 

[A/B]

VFO A

VFO A frequency

VFO B

VFO B frequency

 

[M/V]

Memory Recall1

Channel number

 

 

and frequency

QUICK MEMO

Quick Memory

“Q”, channel number

[MR]

Recall1

and frequency

[MENU]

Menu1

“MENU”, menu number

 

 

and menu selection

[ENT]

Entry 2

“enter”

1When you change the channel or menu number in this mode, the transceiver announces the new number.

2When you enter a number using the numeric keys in Entry mode or Memory Scroll mode, the transceiver announces the entered number.

For the [PF] button, the transceiver will announce different information depending on whether Voice 1 or Voice 2 is selected.

Voice 1:

•VFO or memory channel frequencies are announced beginning with the 10 MHz digit and continuing through to the 10 Hz digit. If the memory channel has no data stored, “open” is announced. For the MHz decimal point, “point” is announced. For the kHz decimal point, a short pause (200 ms) is made. A 200 ms pause also is made between the channel number and the frequency.

•Menu numbers and their settings are announced with a short pause (200 ms) between the menu number and the setting.

Note: If operating a button or a control changes the contents of the display while an announcement is in progress, the announcement is interrupted.

Voice 2:

•Peak readings for the S-meter are announced, for example, “S5” or “20dB”.

Steps:

1Assign Voice 1 or Voice 2 to the front panel [PF] button or, if you use the optional MC-47 microphone, one of the Mic [PF] buttons. For this method, refer to “PROGRAM FUNCTION BUTTON” {page￿49}.

2Press the [PF] button that you programmed.

•Announcement is made based on Voice 1 or Voice 2 selection.

•To interrupt the announcement, press the [PF] button again.

55

Page 60 Page 62
Image 61
Page 60 Page 62
Contents TS-570S Accessory Part Number Supplied AccessoriesApplicable Model Intelligent Digital Enhanced Communications SystemWriting Conventions Followed FeaturesKEY2 Contents Specifications Appendix COM Connector Protocol Index Memory FeaturesScan Operator ConveniencesPower Cable Protection Power SourcePower Lines CleaningAntenna Connection InstallationTransmission Line MHz 14 MHz 30 MHz Installation DC Power Supply ConnectionGround Connection Lightning ProtectionFront Panel Accessory ConnectionsRear Panel DSP Slope High control Fully clockwise DSP Slope LOW control Your First QSOYour Front Panel Getting AcquaintedGetting Acquainted Split button UP/DOWN buttonsTF-SET button Clear buttonMicrophone GND post Rear PanelKEY and Paddle jacks EXT SP jackDisplay @7LSB @6M.SCR@8USB #1FSKAdjusting Volume Switching Power ON/OFFOperating Basics Selecting VFO a or VFO BAdjusting Squelch Selecting a ModeSelecting a Frequency Front Panel MeterTransmitting Selecting Transmit PowerMicrophone Gain What is a MENU? Menu SetupMenu Access Menu A/ Menu BMenu Setup Menu ConfigurationFunction Selections Default GroupSplit Setting Transfer Rate bps Stop BitsCross Reference for Menu Functions SSB Transmission Basic CommunicatingBasic Communicating CW TransmissionAuto ZERO-BEAT TX SIDETONE/ RX Pitch FrequencyAM Transmission FM TransmissionTX Deviation Selection Press FilterSPLIT-FREQUENCY Operation Specialized CommunicatingTF-SET Transmit Frequency SET UP/DWNSpecialized Communicating FM Repeater OperationArrl 10-METER Band Plan Mode/ActivitySpecialized Communicating Selecting Subtone Frequency FM Ctcss OperationContinuous or Burst SUBTONES? Rtty Frequency Shift Keying Digital OperationRtty Frequencies Iaru Region A./CanadaPacket Frequencies Satellite Operation Slow Scan TV/ FacsimileSstv Frequencies Receiving Communicating AidsSelecting Your Frequency Communicating Aids RIT Receive Incremental TuningAGC Automatic Gain Control RX EqualizerPress Delay Delay TimeVOX VOICE-OPERATED Transmit Microphone Input LevelCommunicating Aids Speech Processor XIT Transmit Incremental TuningTransmit Inhibit Monitoring Transmitted SignalsChanging Frequency While Transmitting Changing Transmit Bandwidth SSB/AMAuto Weighting Using Semi BREAK-IN or Full BREAK-INCW BREAK-IN Electronic KeyerBUG KEY Function Communicating Aids Changing LOCKED-WEIGHTCW Message Memory If Filter Rejecting InterferenceNoise Blanker Changing if Filter BandwidthPreamplifier AttenuatorDSP Tools Rejecting InterferenceSetting NR2 Time Constant Beat CancelNoise Reduction CW/ FSK ModesConventional Memory Memory FeaturesStoring Data in Memory Simplex ChannelsSplit-Frequency Channels Memory FeaturesMemory Recall Memory Recall and ScrollTemporary Frequency Changes Memory ScrollMemory-VFO Split Operation To use a memory channel for receivingMemory VFO Transfer Memory Features Memory TransferChannel Channel Transfer Full Reset Memory Features Storing Frequency RangesErasing Memory Channels Confirming Start/End FrequenciesStoring Into Quick Memory Quick MemoryMemory Channel Lockout Press CLRTemporary Frequency Changes Memory Features Recalling Quick MemoryQuick Memory VFO Transfer Program Scan ScanScan Hold Scan Type PurposeScan Memory ScanALL-CHANNEL Scan Group ScanSwitching ANT 1/ ANT Microprocessor ResetOperator Conveniences Frequency Lock FunctionDisplay Dimmer Beep FunctionProgram Function Button Operator ConveniencesUsing Quick Transfer Setting UPQuick Data Transfer Menu Setting Transfer Rate Stop Bits Using a TransverterComputer Control Communication ParametersAutomatic Antenna Tuner PresettingAttune again Message Playback Recording MessagesChecking Messages Sending Messages Changing VolumeChanging Inter-message Interval Menu New Mode AnnouncementVoice StepsDRU-3A Optional AccessoriesPC-1A PG-2ZRemoving the Bottom Case Installing OptionsDRU-3A Digital Recording Unit VS-3 Voice Synthesizer Unit Installing OptionsFilters SO-2 TEMPERATURE-COMPENSATED Crystal Oscillator Tcxo Computer Connecting Peripheral EquipmentCompatible Transceiver Pin No. Pin NameRtty Equipment Connecting Peripheral EquipmentLinear Amplifier Antenna TunerPin No Function MCP and TNCService MaintenanceService Note CleaningMaintenance Internal AdjustmentsAccessing the Internal Fuse Reference Frequency CalibrationProblem Probable Cause Corrective Action TroubleshootingFollowed DSP Slope LOW control orPress LSB/USB, CW/FSK, or Changing ReceivePress LSB/USB or FM/AM to Repeater Operation SSB, CW TS-570S TS-570DFSK, FM SSB, CW, FSK SpecificationsControl Operation Hardware DescriptionAppendix COMAlphabetical Commands Computer Control CommandsError Messages ParametersOFF/ON Alphabetical Command TableFormat Parameter TableUP/DOWN Menu Selection Table for EX CommandI o !0 Computer Control Command TablesDN UP DOWN/UP LK Frequency Lock MG MIC Gain RT RIT RX TX RX, TX VOX Function Sstv VFO
Top Page Image Contents