Kenwood TS-570D Installing Options, Removing the Bottom Case, DRU-3A Digital Recording Unit

Page 63

INSTALLING OPTIONS

The following equipment is required for installing the optional units.

•Large Philips screwdriver

•Small Philips screwdriver

•25 W pencil soldering iron (for the SO-2 unit only)

REMOVING THE BOTTOM CASE

When installing the optional DRU-3A, VS-3, or SO-2 unit, remove the bottom case first.

1Remove the 8 screws.

2Lift off the bottom case.

DRU-3A DIGITAL RECORDING UNIT

CAUTION: SWITCH OFF THE POWER AND UNPLUG THE DC POWER CABLE BEFORE BEGINNING INSTALLATION.

1Remove the bottom case (8 screws).

2Remove the flat cable from the CN15 connector.

CN15

4Plug the DRU-3A connector (CN901) into the CN17 connector.

•The large IC on the DRU-3A must closely contact the cushion on the PC board.

DRU-3A

CN17

5Reconnect the flat cable to the CN15 connector.

6Replace the bottom case (8 screws).

3Peel off the paper backing from the cushion installed on the transceiver PC board.

Cushion

Image 63

Contents TS-570S Intelligent Digital Enhanced Communications System Supplied AccessoriesAccessory Part Number Applicable ModelFeatures Writing Conventions FollowedKEY2 Contents Operator Conveniences Memory FeaturesSpecifications Appendix COM Connector Protocol Index ScanCleaning Power SourcePower Cable Protection Power LinesInstallation Antenna ConnectionTransmission Line MHz 14 MHz 30 MHz Lightning Protection DC Power Supply ConnectionInstallation Ground ConnectionAccessory Connections Front PanelRear Panel DSP Slope High control Fully clockwise DSP Slope LOW control Your First QSOYour Front Panel Getting AcquaintedGetting Acquainted Clear button UP/DOWN buttonsSplit button TF-SET buttonMicrophone EXT SP jack Rear PanelGND post KEY and Paddle jacksDisplay #1FSK @6M.SCR@7LSB @8USBSelecting VFO a or VFO B Switching Power ON/OFFAdjusting Volume Operating BasicsFront Panel Meter Selecting a ModeAdjusting Squelch Selecting a FrequencySelecting Transmit Power TransmittingMicrophone Gain Menu A/ Menu B Menu SetupWhat is a MENU? Menu AccessGroup Menu ConfigurationMenu Setup Function Selections DefaultSplit Setting Transfer Rate bps Stop BitsCross Reference for Menu Functions SSB Transmission Basic CommunicatingTX SIDETONE/ RX Pitch Frequency CW TransmissionBasic Communicating Auto ZERO-BEATPress Filter FM TransmissionAM Transmission TX Deviation SelectionUP/DWN Specialized CommunicatingSPLIT-FREQUENCY Operation TF-SET Transmit Frequency SETMode/Activity FM Repeater OperationSpecialized Communicating Arrl 10-METER Band PlanFM Ctcss Operation Specialized Communicating Selecting Subtone FrequencyContinuous or Burst SUBTONES? Iaru Region A./Canada Digital OperationRtty Frequency Shift Keying Rtty FrequenciesPacket Frequencies Slow Scan TV/ Facsimile Satellite OperationSstv Frequencies Communicating Aids ReceivingSelecting Your Frequency RX Equalizer RIT Receive Incremental TuningCommunicating Aids AGC Automatic Gain ControlMicrophone Input Level Delay TimePress Delay VOX VOICE-OPERATED TransmitCommunicating Aids Speech Processor XIT Transmit Incremental TuningChanging Transmit Bandwidth SSB/AM Monitoring Transmitted SignalsTransmit Inhibit Changing Frequency While TransmittingElectronic Keyer Using Semi BREAK-IN or Full BREAK-INAuto Weighting CW BREAK-INCommunicating Aids Changing LOCKED-WEIGHT BUG KEY FunctionCW Message Memory Changing if Filter Bandwidth Rejecting InterferenceIf Filter Noise BlankerRejecting Interference AttenuatorPreamplifier DSP ToolsCW/ FSK Modes Beat CancelSetting NR2 Time Constant Noise ReductionSimplex Channels Memory FeaturesConventional Memory Storing Data in MemoryMemory Recall and Scroll Memory FeaturesSplit-Frequency Channels Memory RecallTo use a memory channel for receiving Memory ScrollTemporary Frequency Changes Memory-VFO Split OperationMemory Features Memory Transfer Memory VFO TransferChannel Channel Transfer Confirming Start/End Frequencies Memory Features Storing Frequency RangesFull Reset Erasing Memory ChannelsPress CLR Quick MemoryStoring Into Quick Memory Memory Channel LockoutMemory Features Recalling Quick Memory Temporary Frequency ChangesQuick Memory VFO Transfer Scan Type Purpose ScanProgram Scan Scan HoldGroup Scan Memory ScanScan ALL-CHANNEL ScanFrequency Lock Function Microprocessor ResetSwitching ANT 1/ ANT Operator ConveniencesOperator Conveniences Beep FunctionDisplay Dimmer Program Function ButtonSetting UP Using Quick TransferQuick Data Transfer Communication Parameters Using a TransverterMenu Setting Transfer Rate Stop Bits Computer ControlPresetting Automatic Antenna TunerAttune again Recording Messages Message PlaybackChecking Messages Changing Volume Sending MessagesChanging Inter-message Interval Steps New Mode AnnouncementMenu VoicePG-2Z Optional AccessoriesDRU-3A PC-1AInstalling Options Removing the Bottom CaseDRU-3A Digital Recording Unit Installing Options VS-3 Voice Synthesizer UnitFilters SO-2 TEMPERATURE-COMPENSATED Crystal Oscillator Tcxo Pin No. Pin Name Connecting Peripheral EquipmentComputer Compatible TransceiverAntenna Tuner Connecting Peripheral EquipmentRtty Equipment Linear AmplifierPin No Function MCP and TNCCleaning MaintenanceService Service NoteReference Frequency Calibration Internal AdjustmentsMaintenance Accessing the Internal FuseDSP Slope LOW control or TroubleshootingProblem Probable Cause Corrective Action FollowedChanging Receive Press LSB/USB, CW/FSK, orPress LSB/USB or FM/AM to Repeater Operation TS-570S TS-570D SSB, CWFSK, FM SSB, CW, FSK SpecificationsCOM Hardware DescriptionControl Operation AppendixParameters Computer Control CommandsAlphabetical Commands Error MessagesOFF/ON Alphabetical Command TableFormat Parameter TableUP/DOWN Menu Selection Table for EX CommandI o !0 Computer Control Command TablesDN UP DOWN/UP LK Frequency Lock MG MIC Gain RT RIT RX TX RX, TX VOX Function Sstv VFO