Troubleshooting
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
Dolby Digital or DTS | The connected component is not set to | Make an appropriate setting following the operating | — | |
sources cannot be | output Dolby Digital or DTS digital | instructions for your component. |
| |
played. (Dolby Digital | signals. |
|
| |
or DTS indicator in |
|
|
| |
Audio input jack select is set to | Set Audio input jack select to “AUTO”. | 34 | ||
the front panel | ||||
display does not light | “ANALOG”. |
|
| |
up.) |
|
|
| |
|
|
|
| |
A humming sound is | Incorrect cable connections. | Connect the audio cables firmly. If the problem | — | |
heard. |
| persists, the cables may be defective. |
| |
|
|
|
| |
The volume level | You are attempting to set the volume level | Adjust “MAX VOL.” setting. | 55 | |
cannot be increased, | higher than the maximum volume level. |
|
| |
or the sound is |
|
|
| |
The component connected to the AUDIO | Turn on the power of the component. | — | ||
distorted. | ||||
| OUT (REC) jacks of this unit is turned |
|
| |
| off. |
|
| |
|
|
|
| |
The sound effect | It is not possible to record the sound effect | This is not malfunction. | — | |
cannot be recorded. | with a recording component. |
|
| |
|
|
|
| |
A source cannot be | The source component is not connected to | Connect the source component to the analog AUDIO | 15, 19 | |
recorded by an | the analog AUDIO IN jacks of this unit. | IN jacks. |
| |
analog component |
|
|
| |
connected to the |
|
|
| |
AUDIO OUT (REC) |
|
|
| |
jacks. |
|
|
| |
|
|
|
| |
The sound field | “MEMORY GUARD” in “OPTION | Set “MEMORY GUARD” to “OFF”. | 60 | |
parameters and some | MENU” is set to “ON”. |
|
| |
other settings of this |
|
|
| |
unit cannot be |
|
|
| |
changed. |
|
|
| |
|
|
|
| |
This unit does not | The internal microcomputer has been | Disconnect the power cable from the AC wall outlet | — | |
operate properly. | frozen by an external electric shock (such | and then plug it in again after about 30 seconds. |
| |
| as lightning or excessive static electricity) |
|
| |
| or by a power supply with low voltage. |
|
| |
|
|
|
| |
No sound is heard | The HDMI component does not accept the | Convert the | — | |
from the connected | channel audio signals at the source component such |
| ||
HDMI component. |
| as a DVD player. |
| |
|
|
|
| |
“CHECK SP WIRES” | Speaker cables are | Make sure all speaker cables are connected correctly. | 11 | |
appears in the front |
|
|
| |
panel display. |
|
|
| |
|
|
|
| |
There is noise | This unit is too close to the digital or high- | Move this unit further away from such equipment. | — | |
interference from | frequency equipment. |
|
| |
digital or radio |
|
|
| |
frequency equipment. |
|
|
| |
|
|
|
| |
The picture is | The video source uses scrambled or | This in not malfunction. | — | |
disturbed. | encoded signals to prevent dubbing. |
|
| |
|
|
|
| |
This unit suddenly | The internal temperature is too high and | Wait about 1 hour for this unit to cool down and then | — | |
enters the standby | the overheat protection circuitry has been | turn it back on. |
| |
mode. | activated. |
|
| |
|
|
|
| |
The video conversion | Some digital signals are input via HDMI | Turn off the power of the component connected to | 15 | |
function does not | jack. | HDMI IN jacks. |
| |
work. |
|
|
| |
|
|
|
|
INFORMATION | ADDITIONAL |
|
|
English