Using the Speaker OUT jack

When first turning on the sound system, switch on all upstream electronics first, then the PV®115D with its level control fully counterclockwise (all the way down). Begin checking levels with the mixer output level controls all the way down, and bring them up slowly with the PV®115D level control set to the desired setting (one-third of the way up is recommended as a starting point).

The PV®115D has a SPEAKER OUT, a 1 / 4” phone jack output on the rear panel. An external full-range passive speaker system (such as a PV®115) can be connected to this jack, and powered by the internal amplifier. This external speaker must be an 8-ohm impedance or higher. YOU CAN NOT CONNECT A 4-OHM SPEAKER TO THIS JACK, IT WILL CAUSE THE AMPLIFIER TO SHUT DOWN. Impedances lower than 8-ohms nominal are not allowed.

For best results when using this jack, the external speaker connected to it should be of a similar sensitivity to the PV115D, which has a sensitivity around 95 dB for 1w/1M. If the external speaker has a higher sensitivity, it will play louder than the PV®115D, and make it hard to balance the sound in the room. If the external speaker has a lower sensitivity, then it will play softer than the PV®115D does at any given Level control setting.

Another consideration is to place the external speaker as far away as is practical, to increase the overall coverage of the room, and to minimize the interference patterns that occur when two loudspeakers are near one another and radiating the same signal. Placing the external speaker at least 20-25 feet away from the PV®115D would be a good practice. This would correspond to an example of having the PV®115D on one side of a room, and the external speaker on the other side.

USE WITH A PASSIVE ADD-ON SUBWOOFER

Non-powered subwoofers that have a built-in high frequency roll-off (often referred to as “add-on” subwoofers), can also be used with this output, as long as the nominal impedance is 8-ohms or above.

The PV®118 Sub is in this category, and can be used with this output jack. Normally, the closer to the PV®115D the Sub is placed, the better it will work WITH the PV®115D to increase bass output. Since the PV118 Sub has a built-in pole guide for placing a pole stand for the PV®115D, this makes use of a PV®118 Sub a natural for use with the PV®115D.

Use of the PV®115D with a powered Subwoofer

Powered subwoofers often have a built-in electronic crossover to allow a high-pass filtered signal (lows rolled-off) to be sent to the upper range speaker. The PV®118D Sub is such a subwoofer. When using the PV®115D with this type of powered subwoofer, first run the signal from the mixer or signal source to the powered sub input, then come out of the combo jack labeled “THRU/HPF” and send that signal to the PV®115D input jack. On the PV®118D Sub, the button to the far left labeled THRU/HPF should be pushed in to engage the high-pass filter (HPF). On other powered subwoofers, if they have a similar high-pass filter function, send the signal in and out of the subwoofer according to the Manufacturer’s instructions, which should be similar to the instructions as outlined above.

Use of the PV®115D with a Speaker Stand

The PV®115D has a stand mount cup on the bottom so that the system can be stand mounted on a standard 1 3/8” (36mm) diameter stand pole.

When using stands or poles, be sure to follow these precautions:

A.Check the stand or pole specs to make sure that it can support the weight of the PV®115D (56 lbs./25.4 kg), and observe all safety precautions stated by the stand manufacturer, including the maximum height the stand is rated for.

B.Always place the stand on a flat, level and stable surface, and be sure to fully extend the stand legs as per the stand manufacturer’s instructions.

C.Try to make sure that the stand legs are oriented for the least danger of tripping to those in the vicinity of the stand. Never block a doorway or hallway with the legs of a stand.

D.Try to route cables so that people will not trip over them or tip the speaker over. Use of duct tape, cable channels or guards, or other appropriate tie-down/cover –up devices should be carefully considered and implemented.

PV115D specifications

The Peavey PV115D is a powerful and versatile active loudspeaker designed for various applications, from live performances to DJ events and public speaking engagements. With its robust construction and innovative features, this speaker offers a professional sound experience tailored to meet the demands of today’s audio environments.

One of the standout features of the PV115D is its 15-inch heavy-duty woofer, which is designed to deliver deep and accurate bass response. This is coupled with a 1.4-inch titanium diaphragm compression driver that produces crystal-clear highs, ensuring that vocals and instrumentation are reproduced with stunning clarity. The combination of these components enables the speaker to handle a wide frequency range, making it suitable for diverse musical genres and audio content.

The PV115D is equipped with an onboard 300-watt peak power amplifier, which provides adequate headroom for high-volume applications. This built-in amplification eliminates the need for external amplifiers, simplifying setup and reducing gear complexity. Additionally, the speaker features a built-in EQ with preset configurations, allowing users to tailor the audio output to suit specific environments and preferences.

For connectivity, the PV115D includes multiple input options, such as XLR and 1/4-inch TRS inputs, making it compatible with a wide range of audio sources. The speaker also features a microphone input with dedicated volume control, enabling easy integration into live setups where vocal reinforcement is needed.

Durability is a hallmark of the PV series, and the PV115D is no exception. It is housed in a sturdy, textured polypropylene enclosure designed to withstand the rigors of transport and use in various settings. Moreover, the speaker is equipped with a robust, perforated metal grill that protects the drivers while allowing for optimal sound dispersion.

Another advantageous aspect of the PV115D is its lightweight design, which makes it easier to transport and set up. Its integrated handles enhance portability, allowing users to move it with ease, whether for rehearsals, gigs, or events.

In conclusion, the Peavey PV115D is a feature-rich active loudspeaker that offers exceptional sound quality, efficient performance, and robust construction. With its powerful amplifier, versatile connectivity options, and tailored sound shaping, it stands out as an ideal choice for audio professionals and enthusiasts alike.