Connecting AC Power To The PV115D

CAUTIONS

The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to qualified service personnel.

NOTE: This unit is not designed for overhead suspension!

The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from ventilation.

DO NOT connect the inputs of the PV®115D to the output of a power amplifier. The inputs are meant to be driven from a line-level strength signal.

When connecting a microphone to the system, be sure to keep the microphone away from the front of the speaker while setting the microphone level, or very loud feedback will occur! Damage to the system is likely if this occurs!

DO NOT remove the protective metal grille.

WARNING: The PV®115D is very efficient and powerful! This sound system can permanently damage hearing! Use extreme care setting the overall maximum loudness!

The apparent sound level of the PV®115D can be deceiving due to its clear, clean sound output. The lack of distortion or obvious distress can make the sound level seem much lower than it actually is. This system is capable of SPL in excess of 121 dB at 1 meter from the speaker!

Connecting AC Power To The PV®115D

The PV®115D comes with a 6-foot IEC connection AC power cord. If you are using an extension cord or power strip with this powered speaker, make sure it is of good quality and of a sufficient current capacity to maintain safety and maximize the power output capability of the PV®115D. Do not connect any other device to the same extension cord that the PV®115D is connected to.

Connecting a Signal to the PV®115D

There are a variety of ways to input a signal to the PV®115D. The input jack (5) provides a balanced line-level input, allowing the use of a 1/4” phone plug, either a standard single-ended (tip-sleeve) plug or a balanced TRS (ring-tip-sleeve) type plug OR a male XLR plug.

Do not connect cables to the jacks while the unit is ON and the Level is turned up!

While a standard shielded single-ended 1/4” phone plug-equipped cable will work well and the balanced input circuitry of the input jack (5) will provide some interference rejection, a balanced cable using either the balanced TRS 1/4” phone plug or the XLR plug will provide superior interference rejection and performance. Sometimes, with difficult interference problems, it will be helpful to lift the shield ground on a balanced cable at the PV®115D end. Check any input changes carefully, always turning the volume control down before plugging and unplugging cables or making grounding changes.

Use of high quality, premium cables is recommended for the PV®115D, as these usually have better shielding and materials and will provide greater long-term reliability. It is usually a good idea to leave some slack at the input to the PV®115D and also to tape the cables down or run them under a cable guard to avoid anyone tripping over them or pulling the PV®115D over when stand mounted.

Level Control Adjustment

The PV®115D is equipped with a level control (6) to facilitate use in many different applications. With the level control adjusted fully clockwise, gain is at maximum and the input sensitivity is 0.650 V RMS for full-rated output. When driving the PV®115D from a mixer, it may be advantageous to reduce the input sensitivity by turning the level control to the halfway point or even less. The PV®115D will now more closely match the sensitivity of a typical power amp.

If the mixing board indicates clipping of its output signals, then all of the PV®115D power capability is not being utilized cleanly. Clipping the signal before it gets to the PV®115D is not optimal. Reduce the mixer output level and turn up the level control on the PV®115D.

The amplifier in the PV®115D is equipped with DDT™ and an LED indicator to show that DDT™ has engaged. If the sound seems heavily compressed, check this indicator; if it is blinking RED more than occasionally, then the drive level from the mixer (or the level control on the PV®115D) needs to be reduced.

PV115D specifications

The Peavey PV115D is a powerful and versatile active loudspeaker designed for various applications, from live performances to DJ events and public speaking engagements. With its robust construction and innovative features, this speaker offers a professional sound experience tailored to meet the demands of today’s audio environments.

One of the standout features of the PV115D is its 15-inch heavy-duty woofer, which is designed to deliver deep and accurate bass response. This is coupled with a 1.4-inch titanium diaphragm compression driver that produces crystal-clear highs, ensuring that vocals and instrumentation are reproduced with stunning clarity. The combination of these components enables the speaker to handle a wide frequency range, making it suitable for diverse musical genres and audio content.

The PV115D is equipped with an onboard 300-watt peak power amplifier, which provides adequate headroom for high-volume applications. This built-in amplification eliminates the need for external amplifiers, simplifying setup and reducing gear complexity. Additionally, the speaker features a built-in EQ with preset configurations, allowing users to tailor the audio output to suit specific environments and preferences.

For connectivity, the PV115D includes multiple input options, such as XLR and 1/4-inch TRS inputs, making it compatible with a wide range of audio sources. The speaker also features a microphone input with dedicated volume control, enabling easy integration into live setups where vocal reinforcement is needed.

Durability is a hallmark of the PV series, and the PV115D is no exception. It is housed in a sturdy, textured polypropylene enclosure designed to withstand the rigors of transport and use in various settings. Moreover, the speaker is equipped with a robust, perforated metal grill that protects the drivers while allowing for optimal sound dispersion.

Another advantageous aspect of the PV115D is its lightweight design, which makes it easier to transport and set up. Its integrated handles enhance portability, allowing users to move it with ease, whether for rehearsals, gigs, or events.

In conclusion, the Peavey PV115D is a feature-rich active loudspeaker that offers exceptional sound quality, efficient performance, and robust construction. With its powerful amplifier, versatile connectivity options, and tailored sound shaping, it stands out as an ideal choice for audio professionals and enthusiasts alike.