Sharp PN-K321 operation manual Menu Items NSETUP, Nmonitor, NPbyP

Page 20

Menu Items

nSETUP

LANGUAGE

Sets the display language for the menu screen.

INPUT SELECT

HDMI1/HDMI2

Select the input modes to be used for the PC/AV HDMI1 and HDMI2 input terminals.

HDMI DUAL

To use HDMI DUAL, select ON.

AUDIO SELECT

Selects the terminal used to input audio signals in each input mode.

When HDMI DUAL is used, the HDMI1 settings are applied.

AUDIO INPUT LEVEL

Selects the maximum audio input level of the audio input terminal.

BAUD RATE

Selects the communication speed used for RS-232C communication.

DisplayPort STREAM

When using a screen resolution of 3840 x 2160 (50Hz/60Hz) in the DisplayPort input terminal, select MST (Multi-stream). Images may not be displayed properly with some video card combinations.

nMONITOR

MONITOR

Select the installation direction of the monitor.

LANDSCAPE

Landscape orientation

PORTRAIT

Portrait orientation

If the monitor is in a portrait orientation and a Windows PC is connected, set “Orientation” to “Portrait (Flipped)” in the “Screen Resolution” settings.

If you are using a different operating system, refer to the manual for your operating system.

OFF IF NO OPERATION

Determines whether or not to set the monitor go into standby mode when no monitor button or RS-232C command operations are performed for over 4 hours.

nPbyP

PbyP MODE

Sets the display method.

OFF .........Displays one screen.

ON ...........Displays a main screen and a sub screen in a line.

*When using PbyP mode, set HDMI DUAL to OFF and DisplayPort STREAM to SST (Single Stream).

PbyP SOURCE

Select the input signal of the sub-screen in PbyP mode.

When the input mode is DisplayPort

HDMI1 or HDMI2

When the input mode is HDMI1

DisplayPort or HDMI2

When the input mode is HDMI2

DisplayPort or HDMI1

E20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PN-K321 Page Refer Servicing to Qualified Service Personnel Important InformationDear Sharp Customer Safety Precautions Tips and Safety Instructions For the monitor in landscape orientation For the monitor in portrait orientationBack FrontContents Supplied ComponentsAttachment plate for stand Brightness adjustment button Part NamesNFront view NRear viewInstalling the stand supplied NAttaching the standInstalling the stand supplied NHeight/angle adjustment Adjusting the heightAdjusting the angle 11 EConnecting Peripheral Equipment Connecting the Power Cord 13 ENStoring the cables Binding CablesNFastening the cables 15 E Turning Power On/OffPower lamp status Status of the monitor Basic Operation Basic Operation NSwitching the screen size 17 EWide Normal Dot by DotMenu Items NExample of operationNMenu screen display ContrastNPICTURE 19 EMenu Items NPbyP Menu Items NSETUPNMONITOR 21 E Menu Items NOTHERSMenu Items NDual screen display NHDMI DualPbyP HDMI1 HDMI223 E Volm NCommand formatControlling the Monitor with a PC RS-232C When a command has been executed correctly When a command has not been executedIf execution of the command is taking some time 25 EControlling the Monitor with a PC RS-232C Power control/Input mode selectionHow to read the command table 27 E Controlling the Monitor with a PC RS-232C Picture menuControlling the Monitor with a PC RS-232C Setup menu Monitor menuPbyP menu Others menu29 E OthersTroubleshooting Specifications NProduct Specifications31 E Vesa DDC2BSpecifications NDimensional Drawings Unit inch mmSpecifications NCompatible signal timing PC Screen resolution Vsync DisplayPort33 E HDMI1 Hdmi Dual *1NDDC plug and play Specifications NCompatible signal timing AVNPower management NDisplayPort input terminal pins Specifications NPC/AV Hdmi input terminal pinsHdmitm Connector 35 ENToppling prevention NRemoving the attachment plateTop of monitor Back of monitorPN-K321 Ma EN13D3
Top Page Image Contents