Sharp Installation Precautions and Guidelines for the PN-K321 Monitor
Page 36

Mounting Precautions

(For SHARP dealers and service engineers)

•When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.

•Be sure to use a wall-mount bracket designed or designated for mounting the monitor.

•This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation.

This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.

•To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the thickness of the mounting bracket.

•Do not use an impact driver.

•When moving the monitor, be sure to hold it with the unit bottom and the side of unit. Do not hold the LCD panel or corners. This may cause product damage, failure, or injury.

•Do not use any screw holes other than VESA holes for installation.

nToppling prevention

Caution

•To reduce the risk of injury and damage caused by the product toppling or falling in an earthquake or similar situation, take measures to prevent toppling and falling.

•If the wall or platform on which the monitor is installed is not sufficiently strong, the effectiveness of the toppling/ falling prevention measures will be severely compromised. Reinforce the wall or platform as needed.

The toppling/falling prevention measures are intended to reduce the risk of injury and damage in an earthquake, however, the effectiveness of the measures is not guaranteed in all earthquakes.

•Before implementing the toppling prevention measures, complete all connections.

Secure to wall or post

1.Attach a commercially available eye bolt (a bolt shaped to allow attachment of a string or cord) to the wall or post.

Verify that the eye bolt is attached firmly and does not come out.

•Top of monitor

nRemoving the attachment plate

Caution

•The attachment plate is only for use with the monitor. Do not use with any other devices.

1.Spread a thick, soft cloth (blanket, etc.) that will prevent damage to the LCD panel on a stable flat surface where the entire monitor can be placed, and place the monitor with the LCD panel face down on the cloth.

2.Remove the screws(x4) that fasten the attachment plate, and remove the attachment plate.

Commercially available eye bolt (bolt shaped to allow attachment of a string or cord)

2.Run a commercially available cord of sufficient strength through the cable clamp attachments and the eye of the eye bolt on the wall or post to secure the monitor.

•Top of monitor

Commercially available cord

• Back of monitor

E36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents PN-K321 Page Refer Servicing to Qualified Service Personnel Important InformationDear Sharp Customer Safety Precautions Tips and Safety Instructions For the monitor in landscape orientation For the monitor in portrait orientationBack FrontContents Supplied ComponentsAttachment plate for stand Brightness adjustment button Part NamesNFront view NRear viewInstalling the stand supplied NAttaching the standInstalling the stand supplied NHeight/angle adjustment Adjusting the heightAdjusting the angle 11 EConnecting Peripheral Equipment Connecting the Power Cord 13 EBinding Cables NFastening the cablesNStoring the cables Turning Power On/Off Power lamp status Status of the monitor15 E Basic Operation Basic Operation NSwitching the screen size 17 EWide Normal Dot by DotMenu Items NExample of operationNMenu screen display Contrast19 E Menu ItemsNPICTURE Menu Items NSETUP NMONITORNPbyP 21 E Menu Items NOTHERSMenu Items NDual screen display NHDMI DualPbyP HDMI1 HDMI223 E NCommand format Controlling the Monitor with a PC RS-232CVolm When a command has been executed correctly When a command has not been executedIf execution of the command is taking some time 25 EPower control/Input mode selection How to read the command tableControlling the Monitor with a PC RS-232C 27 E Controlling the Monitor with a PC RS-232C Picture menuControlling the Monitor with a PC RS-232C Setup menu Monitor menuPbyP menu Others menu29 E OthersTroubleshooting Specifications NProduct Specifications31 E Vesa DDC2BSpecifications NDimensional Drawings Unit inch mmSpecifications NCompatible signal timing PC Screen resolution Vsync DisplayPort33 E HDMI1 Hdmi Dual *1Specifications NCompatible signal timing AV NPower managementNDDC plug and play NDisplayPort input terminal pins Specifications NPC/AV Hdmi input terminal pinsHdmitm Connector 35 ENToppling prevention NRemoving the attachment plateTop of monitor Back of monitorPN-K321 Ma EN13D3
Top Page Image Contents