Jensen MS4200RS user manual Initial operation, Fig, Checking the vehicle functions

Page 10

INSTALLATION INSTRUCTIONS

Initial operation, Fig. 12

1.Reconnect the battery.

2.Restore complete functioning of the electrical system (clock, trip computer, alarm system, airbag, immobilizer, etc.).

3.Switch on the ignition.

4.Insert the map CD in the radio. To register the system and activate map, travel and/or traffic info, see the operating instructions, Section “C-IQ”, page 32.

5.Park the vehicle outdoors to ensure unimpeded GPS reception.

6.Switch on the ignition and the radio.

7.Push the NAVIGATION button and confirm the user information with the OK button. The main menu appears. The navigation radio will now initialize.

After connection of the power supply, the integrated GPS receiver requires approximately 2 to 10 minutes until GPS reception is satisfactory.

Setting the mounting angle

In order to ensure perfect functioning of the system, the navigation radio must be set to the actual installation angle in the instrument panel.

1.In navigation mode: Select the “Mounting angle” option in the “System settings” menu.

2.Depending upon the installation, set the angle to between -10 and +30 degrees. The system does not differentiate between negative and positive angles. Thus, even for a mounting angle of, e.g. -10 degrees, set a value of “10" in the menu.

Loudspeaker test

To check the correct connection of the loudspeakers the function “Loudspeaker Test” in the “INITIALIZATION” menu can be performed. page 30.

Setting the clock and the time zone

To ensure that the correct time is always displayed, select the “GPS” option in the “INITIALIZATION” menu under “Clock Settings” and set the time zone for your location. page 30.

Checking the vehicle functions

ACheck the safety-relevant vehicle functions only when the car is stationary, or moving at low speed. Only perform the check in an open area.

Brake system, alarm system, lights, immobilizer, speedometer, trip computer, clock.

Checking GPS reception

Enter a destination and select “Guidance”. Call up the “GPS / Compass” information menu via the guidance screen (see operating instructions) and check the number of satellites. For a sufficiently exact location determination the number should be between 4 and 8.

Calibrating the system

For automatic calibration, perform a short test drive (approx. 10 minutes) on digitized roads. Change direction several times.

k

7

Image 10
Contents MS4200RS Table of Contents IQ Intelligent Content on Demand Important notes for safe usage Class 1 laser productObey all traffic signs and laws while driving Safety and Warnings Taking safety precautions, Fig Connection in vehicles without standard ISO connectorsMaking the electrical connections Telephone mute function A3, optional Connection overview, ISO connector A, FigVolt battery A4 Volt ignition A7Yellow connector C1 Preamp line-out Connection overview ISO connector B loudspeakers, FigConnection overview ISO connector C Blue connector C3 CD changerInstall installation bracket Installing the GPS antenna, FigMounting the radio, Fig Initial operation, Fig Checking the vehicle functionsTechnical Support How does the navigation system work? Start-up characteristicsRoute & Sound Navigating and listening to an audio CD Important notes on the function of your navigation radioAreas with limited road information Digital road mapComments Topicality of the map CDAnti-theft protection LED Removable operating panelSecurity code Removing the operating panelRDS Radio Data System Handling CDsControl elements TELCD changer mode Radio modeCD player mode Navigation modeInserting a CD Switching on / offVolume Removing a CDActive option Option Inactive option Menu operationReturn CursorEntering letters CityW ‰ ¡ Z ¯Activating functions in expert mode Choosing the user modeActivating functions in common mode Normal and expert modesTMC Scan Information menuTA Scan News Ann. level Displayed message … Behavior of TMC and TATraffic announcements from other stations EON Sound Settings Sound menuPage Setting stations RadioRadio Autostore Store Preset Recall ProgramRadio menu RDS MemoPTY search only on FM Radio SetupExtra info InitializationSelecting a function CD playerCD playback CD Player RndScan CD menuRepeat Track CD Title Extra Info 1044 CD changer accessoriesCD changer playback Selecting a CDRandom Repeat Track Select CD CD Changer SetupCD Changer menu RandomBeep Level Clock SettingsInitialization menu Scan Time 15s On Off LogicUser On Off LogicDisplay IconsRegistering the navigation system IQ Your key to map, traffic and travel informationActivation options Navi ID Navi ID 8Q6S 7ED4 CD EUR 2003/01 NT SW IDCode Input Activating productsMy C-IQ R 5 Z 4 a KPreview IQ SettingsIQ Service IQ InfoMain menu Destination input New address Destination inputDestination input menu Load address Last destin. Info on car posI.....O Entering a new addressCityW CountryStep Route selection Step RoadStep House number or intersection Directly to guidanceSpecial facilities of national importance Points of interest POIsSpecial facilities in connection with the destination Destination input via GPS coordinates Special facilities in the vicinity of the current position26 km Via point input Via point input New addressDelete via points not reached Mls GuidanceImproved acoustic guidance information Turn now adviceAudible messages Repeating voice message4,1mls UI 0245pm Guidance beyond digitized roadsAreas with limited road information 15 mls UI 1127amRoute selection B49 Mls Information during guidanceAb Anschl Mls A45 18.8 Destination 04/02/03 812 am Trip computer 35 mph 24 mph Mph 235 mlsDisplaying / deleting via points GPS / CompassAlternative route Cancel procedureAlternative route YesDelete address Address managerStoring addresses in the address book Delete via pointsDeleting list of last destinations Store current locRenaming addresses GPS position Emergency menuEmergency Car positionSpeed System settingsGuidance screen Dyn. route sett. Language Dyn. route sett Settings for dynamic route planningGuidance screen LanguageMounting angle Default settingsService System InfoLoading software updates Troubleshooting Symptoms Possible cause / remedyNavigation Month Limited Warranty Specifications CEA Power RatingsPage 033104

MS4200RS specifications

The Jensen MS4200RS is a highly regarded marine audio system designed for boating enthusiasts who prioritize high-quality sound and durability in a marine environment. This versatile unit combines the latest technological advancements with rugged features tailored for marine applications, making it a top choice for boaters.

One of the standout features of the Jensen MS4200RS is its extensive compatibility with multiple audio sources. It integrates seamlessly with Bluetooth, allowing users to connect smartphones or other devices wirelessly to stream music effortlessly. Additionally, it has built-in support for AM/FM radio, providing access to a wide array of radio stations for on-the-water entertainment.

The unit's user-friendly interface is another commendable aspect of the Jensen MS4200RS. It is equipped with a large, backlit LCD display, ensuring visibility even in bright sunlight. The intuitive controls allow for easy navigation through playlists, radio stations, and settings, facilitating a hassle-free user experience while cruising.

One of the critical considerations for marine audio systems is durability. The Jensen MS4200RS boasts a marine-grade design, complete with a weather-resistant rating. This resilience against splashes and humidity means that boaters can enjoy their favorite tunes without worrying about damage from the marine environment. The unit is built to endure the rigors of outdoor use, making it an ideal companion for any sea voyage.

Sound quality is paramount in any audio system, and the Jensen MS4200RS delivers impressive audio performance. It features a built-in amplifier that provides ample power to drive speakers, resulting in clear and powerful sound across a wide frequency range. Additionally, the unit includes customizable equalizer settings, allowing users to tailor the audio output to suit their preferences or the acoustics of their boat.

Moreover, the MS4200RS is designed with expandability in mind. It supports multiple audio outputs, enabling users to connect additional speakers or subwoofers, thereby enhancing the overall audio experience. The versatility of the system caters to the needs of both casual listeners and audiophiles alike.

In summary, the Jensen MS4200RS represents an excellent choice for marine audio enthusiasts. With its robust features, advanced connectivity options, user-friendly controls, and durability, it stands out as a reliable companion for music lovers on the water. Whether for a leisurely day on the lake or a more adventurous sea journey, the Jensen MS4200RS promises quality sound and performance in a marine-friendly package.