NEC LCD1960NX manual Troubleshooting, No picture

Page 15

Troubleshooting

No picture

¥The signal cable should be completely connected to the display card/computer.

¥The display card should be completely seated in its slot.

¥Check the Vacation Switch should be in the ON position.

¥Front Power Switch and computer power switch should be in the ON position.

¥Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.)

¥Check the monitor and your display card with respect to compatibility and recom- mended settings.

¥Check the signal cable connector for bent or pushed-in pins.

Power Button does not respond

¥Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.

¥Check the Vacation Switch on the right side of the monitor.

Image Persistence

¥Image persistence is when a residual or ÒghostÓ image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitorsÕ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE: As with all personal display devices, NEC-Mitsubishi Electronics Display recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

Image is unstable, unfocused or swimming is apparent

¥Signal cable should be completely attached to the computer.

¥Use the OSM Image Adjust controls to focus and adjust display by

increasing or decreasing the fine total. When the display mode is changed, the OSM Image Adjust settings may need to be re-adjusted.

¥Check the monitor and your display card with respect to compatibility and recommended signal timings.

¥If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.

LED on monitor is not lit (no green or amber color can be seen)

¥ Power Switch should be in the ON position and power cord should be connected.

Display image is not sized properly

¥Use the OSM Image Adjust controls to increase or decrease the Coarse total.

¥Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.)

No Video

¥If no video is present on the screen, turn the Power button off and on again.

¥Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).

13

LCD1960NX050603.p65

13

5/21/03, 1:07 PM

Image 15
Contents MultiSync LCD1960NXTM Index FCC Information Canadian Department of Communications Compliance StatementContents Quick Start Turn off the power to your computerFigure C.1 Vacation Switch Raise and Lower Monitor Screen TiltSwivel Figure S.1 Remove Monitor Stand for MountingAccuColor Control Systems ControlsMenu Brightness/Contrast ControlsInformation ToolsRecommended Use Safety Precautions and MaintenanceErgonomics Monitor MultiSync LCD1960NX Specifications SpecificationsFeatures No picture TroubleshootingReferences NEC-Mitsubishi Monitor Customer Service & SupportLimited Warranty MultiSync LCD1960NX L192R9 Black Model TCO’99FAX Number +46 8 782 92 Mail Internet development@tco.se TCO’99MultiSync LCD1960NX L192R9 White Model TCO’03TCO’03 Declaration of the Manufacturer Informations FCC AvertissementLa bote* de votre nouveau moniteur NEC MultiSync¨ contient ContenuMettez lÕordinateur hors tension Mise en marche rapideFigure C.1 Interrupteur de Vacances Mise en marche rapide suiteNota Manipule sur soin quand lÕŽcran inclinant Žcran Levez et baissez l’écran du moniteurIncliner PivoterDépose du support du moniteur pour montage Exit CommandesOutils Commandes suiteInformation Consignes de sécurité et d’entretien Usage recommandéErgonomie Usage recommandé suiteFiche technique Fonctions Pas dimage DépannageRéférences Techform.htmSŽlectionne ÒDownloads and DriversÓ Garantie limitée Exigences environnementales MultiSync LCD1960NX L192R9 Pour Noir la ModélePourquoi des ordinateurs «éco-étiquetés»? Qu’est-ce qu’implique l’éco-étiquetage?Mercure TCO’99 suitePlomb CadmiumMultiSync LCD1960NX L192R9 Pour Blanche la Modéle TCO’03 C’est une traduction de portion Anglaise de TCO’03TCO’03 suite Déclaration du fabricant Déclaration DE Conformité Declaration of Conformity