Kenwood TH-D7A instruction manual Beep ON/OFF, Press F, ENT to switch Tone Alert on or OFF

Page 53

TONE ALERT

Tone Alert provides an audible alarm when signals are received on the frequency you are monitoring. In addition, it shows the number of hours and minutes elapsed after signals were received. If you use Tone Alert with CTCSS, it alarms only when a received CTCSS tone matches the tone you selected.

1Press [A/B] to select band A or B.

•If necessary, press [F], [A/B] to recall the sub-band.

2Press [F], [ENT] to switch Tone Alert ON (or OFF).

•A bell icon appears when Tone Alert is ON.

STA CON PACKET96 BCONDUP

5 7 9

•When a signal is received, an alarm sounds and the bell icon starts blinking.

•Pressing the PTT switch while the bell icon is blinking switches Tone Alert OFF.

•When 99 hours and 59 minutes pass after a signal is received, counting stops.

•Each time a new signal is received, the time resets to 00.00.

Note:

◆While Tone Alert is ON, there is no speaker output when a signal is received. To hear receive audio, press and hold [MONI].

◆When Tone Alert is ON, APO does not turn the power OFF.

◆When Tone Alert is ON, you can use only the following functions:

•

Lamp ON

•

Lamp Latch ON

•

Monitor

•

Band A/B Select

•Squelch Level Select

BEEP ON/OFF

The transceiver beeps each time you press a key on the keypad. You can also switch this function OFF. Access Menu 1–5–3 (BEEP) and select “OFF”. The default is “ALL”.

In Menu 1–5–3 you can also select “KEY” and “KEY+NEW DATA”. Those settings are described in “APRS” sections {pages 63 and 77}.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

47

Page 52 Page 54
Image 53
Page 52 Page 54
Contents TH-D7A Models Covered by this Manual FeaturesThank YOU One or more of the following statements may be applicable PrecautionsContents System Ctcss ScanFunctions Microphone ControlSKY Command 2 TH-D7A only Wireless Remote Control TH-D7A onlyMaintenance Optional AccessoriesKEY+ Power on Supplied AccessoriesConventions Followed in this Manual KEY2Insert the charger AC plug into an AC wall outlet Latch, then slide the battery pack backPreparation Installing the Hand STRAP/ Belt Hook Installing the AntennaBatteries PB-39 NiCd PB-38 NiCdAlkaline Installing Alkaline Batteries10 2 Insert four AA LR6 alkaline batteries Connecting with a Cigarette Lighter Socket Connecting with a Regulated Power SupplyFirst QSO Adjusting Volume Switching Power ON/OFFOperating Basics Selecting a BandPress OK to complete the setting Adjusting SquelchPress F, Moni Press UP/ DWN to select from 6 squelch levelsSelecting lower transmit power is a wise method to When you finish speaking, release the PTT switchReduce battery consumption, if communication is still Reliable. You can program a different power for bandGetting Acquainted Indicators Band a & B Cursor KeysUP/ DWN keys OK keyVFO mode Function Select modeMemory Recall mode Menu modePacket mode Full Duplex modeCommands to the built-in TNC from a personal computer Press TNC twice to select. In this mode, you can sendKeypad Direct Entry Menu SET-UP Menu AccessLevel Selections Default Menu ConfigurationLevel Selections Radio AUXAprs OFFCMD SstvSKY Offset Programming Flow Operating Through RepeatersPress UP/ DWN to select the appropriate offset Frequency Programming OffsetFollowing methods to bring the transmit frequency Within the band limits67.0 97.4 136.5 192.8 Press F, 1 to switch the Tone function on or OFFPress UP/ DWN to select the appropriate tone frequency A. and Canada versions Automatic Repeater OffsetPress REV 1 s to switch the function on Press REV to switch the Reverse function on or 13 OFFReverse Function Automatic Simplex Check ASCTone FREQ. ID CHANNEL? Memory ChannelsParameter Ctcss onPress PTT+OK Press UP/ DWN to select the desired memory channel Press OKRecalling a Memory Channel Press MR+ Power onClearing a Memory Channel Press UP/ DWN to select the desired memory ChannelRepeat steps 3 and 4 to enter up to 8 digits Naming a Memory ChannelPress UP/ DWN to select the first digit Press PTT+CALL Call Channel TH-D7A onlyPress VFO Channel Display MEMORY-TO-VFO TransferPress F+ Power on Partial or Full RESET?VHF Band Defaults Version VFO Freq Tone UHF Band DefaultsScan Type Scan Range ScanThis transceiver provides the following types of scans Carrier-Operated mode Time-Operated modeSeek mode Selecting Scan Resume MethodMemory Scan VFO ScanPress VFO 1 s Press MR 1 sTo quit MHz Scan, press ESC MHz ScanPress F, MR Program ScanSelect the desired frequency as the lower limit Recall the desired memory channel CALL/VFO Scan TH-D7A onlyCALL/MEMORY Scan TH-D7A only Selecting a Ctcss Frequency Continuous Tone Coded Squelch System CtcssPress F, 4 to select F-4 Ctcss Freq Press UP/ DWN to select the appropriate Ctcss frequencyPress F, 3 to switch the Ctcss function on or Using CtcssCtcss FREQ. ID OFFFreq. Hz 1209 1336 1477 1633 Dual Tone MULTI-FREQUENCY Dtmf FunctionsManual Dialing Press OK Automatic DialerPress UP/ DWN to select a character Press PTT+MENU Transmitting a Stored Dtmf NumberCtcss ON/ OFF Microphone ControlDirect Frequency Entry Auxiliary FunctionsData is accepted for the digits entered and 0 is Programmed for the digits not yet enteredProgrammable VFO Changing Frequency Step SizeBeep ON/OFF Press F, ENT to switch Tone Alert on or OFFTone Alert Adjusting Display Contrast Adjusting Volume BalanceLamp Function Blanking a Band DisplayBattery Saver Automatic Power OFF APOTransceiver Lock POWER-ON Message13 3 Press UP/ DWN to select a character 15 4 Press OKSwitching TX Deviation TH-D7E only Switching AM/FM Mode TH-D7A onlyTX Inhibit Advanced Intercept Point AIPReference material for starting packet operation should Packet OperationBe available at any store that handles Amateur Radio EquipmentCommand mode Connecting with a Personal ComputerConverse mode Operating TNCFollowing steps should guide you to a good start Preparation FlowPacket operation. The shaded steps indicate operations On your personal computer. First connectFull Duplex Selecting Data BandBand only Both BandsDX Packetclusters Monitor Comment Press List to restore the frequency displaySLOW-SCAN Television Sstv with VC-H1 22 4 Press OK Entering Call SIGN/ MESSAGE/ RSV20 3 Press UP/ DWN to select a character Selecting Color for Call SIGN/ MESSAGE/ RSV Executing SuperimpositionVC-H1 Power is onVC-H1 Control Automatic PACKET/ Position Reporting System Operation Flow Receiving Aprs Data Indicator Meaning What is Included?New Aprs Duplicate KEYPress List Accessing Received Aprs Data12 2 Press UP/ DWN to select the desired station 18 3 Press OKTemperature 11 3 Press UP/ DWN to select a character Programming a Call Sign13 4 Press OK 15 5 Repeat steps 3 and 4 to enter up to 9 digitsSelecting Your Station Icon Press OK Press Menu to exit Menu modePress UP/ DWN to select from 15 icons plus Others Kenwood SstvPress 2, 3 to select 2-3 My Pos Press Menu to enter Menu modeEntering LATITUDE/ Longitude Data Press UP/ DWN to select the desired comment Selecting a Position Comment17 4 Press OK Entering Status TextPress UP/ DWN to select a character All calls Programming a Group CodeSpecial Alternate netRepeat steps 3 and 4 to enter up to 32 digits Programming a Packet PathMethod 2 Generic path Method 1 Specific pathMethod 3 WIDEN-N path Method 4 Ssid pathBcon again Selecting Beacon Transmit MethodPress 2, 9 to select 2-9 Data TX Restricting Reception of Aprs Data Selecting Beacon Transmit IntervalPress UP/ DWN to select the desired interval Press UP/ DWN to select the desired distanceAprs Message KEY+NEW Data Press MSG Accessing Received Aprs MessagesMessage Type StatusRepeat to enter a message or bulletin with up to 45 digits Entering a MessageRepeat steps 4 and 5 to enter up to 9 digits Press OK to start transmitting Transmitting a MessagePress PTT+VFO+ Power on Wireless Remote Control TH-D7A onlyPreparation Press a numeric key 0 to 9 to enter a 3-digit secret numberENT or VFO UP/ DWN To recall a memory channel Press PTT+MR+ Power onControl Operation SKY Command 2 TH-D7A only You can use the optional cables PG-4R to connect TransceiverTransporter with the HF transceiver. For these cables Contact your authorized Kenwood dealerOn the Commander Access Menu 4-4 and select Commander Programming Call Signs On CommanderProgramming a Tone Frequency On TransporterUP/ DWN PowerMode CLRPage Service MaintenanceService Note CleaningPress A/B+ Power on to exit TroubleshootingProblem Probable Cause Corrective Action Press BAL, then UP/ DWN to Page Problem Probable Cause Corrective Action SMC-32 SMC-33 SMC-34 Optional AccessoriesHMC-3 EMC-3 PB-38 PB-39 BT-11PG-4W PG-3JVC-H1 PG-4V PG-4REquipment Connections Connecting Other External EquipmentGeneral VHF Band UHF Band SpecificationsTransmitter VHF Band UHF Band Appendix TNC Commands ListShort Default Parameter Description Echo ON/ OFF DwaitFirmrnr FIR OFF ON/ OFF Flow ON/ OFFLocation LOC Every HbaudLpath LPA GPS LtextTxdelay ResetPersist Ppersist ON/ OFFQuick Reference Guide VFO F Key Operation Function1 s Index
Related manuals
Manual 112 pages 51.12 Kb Manual 112 pages 51.23 Kb

TH-D7A specifications

The Kenwood TH-D7A is a sophisticated handheld transceiver designed especially for amateur radio enthusiasts. It combines advanced features with user-friendly operation, making it a popular choice among both beginners and seasoned operators.

One of the standout features of the TH-D7A is its dual-band capability, allowing users to operate on both the 2-meter (144 MHz) and 70-centimeter (440 MHz) bands. This dual-band functionality gives operators increased flexibility and access to a wider range of communication channels. Additionally, the transceiver supports the simultaneous transmission and reception of two different frequencies, allowing for efficient monitoring of multiple communications.

The TH-D7A is equipped with an impressive 1,000 memory channels, which can be organized into 100 memory groups. This allows users to store a vast amount of frequencies and access them easily when needed. The transceiver also provides a wide frequency coverage, extending from 144 to 148 MHz and from 430 to 450 MHz in the VHF and UHF bands, respectively.

Another remarkable feature of the TH-D7A is its built-in Automatic Packet Reporting System (APRS) capabilities. This technology enables users to share real-time location data, send and receive messages, and provide status updates, making it an invaluable tool for outdoor activities and emergency communication.

In terms of construction, the TH-D7A features a durable and compact design, making it suitable for both portable and mobile use. The large, easy-to-read LCD display provides clear visibility in various lighting conditions. Additionally, the transceiver supports a variety of advanced voice modes, including FM, AM, and SSB (Single Side Band), offering a versatile communication experience.

The TH-D7A also incorporates a wide range of digital modes, enhancing its operational capabilities. With the included programming software, users can easily customize their settings, manage memory channels, and update firmware, ensuring the transceiver remains compatible with evolving technologies.

Power management is another highlight, as the TH-D7A provides adjustable output power levels, enabling users to conserve battery life when needed. Overall, the Kenwood TH-D7A is a feature-rich handheld transceiver that combines robust performance with innovative technology, making it a top choice for amateur radio operators seeking reliable communication in diverse environments. Its versatility, combined with its intuitive design, ensures it meets the needs of users across all experience levels.
Top Page Image Contents