Kenmore 153.33207, 153.33204, 153.33206, 153.33205 owner manual Troubleshooting Guidelines

Page 31

TROUBLESHOOTING GUIDELINES

These guidelines should be used by a qualified service agent. Call Sears Service at 1-800-4-MY-HOME®(1-800-469-4663)

for assistance. Inform the associate that this is a “Flammable Vapor Ignition Resistant” Product.

#

7

8

9

10

11

12

13

14

15

16

LED STATUS

PROBLEM

 

SOLUTION

 

 

The gas control valve has detected

1

Turn the power off for 10-20 seconds then on again to

 

 

 

 

 

clear these error codes.

 

 

 

 

 

a problem with the gas valve driver

 

 

 

 

 

 

 

circuit, internal microprocessor, or

2

If any of these error codes persist or cannot be cleared

 

 

other internal circuits.

 

 

 

- replace the gas control valve.

 

 

 

 

 

 

The gas control valve has sensed

1

Turn the power off for 10-20 seconds then on again to

 

 

 

 

 

clear these error codes.

 

 

main burner flame out of proper

 

 

 

 

 

 

 

sequence.

2

Replace the gas control valve if this error code persists.

 

 

 

 

 

 

 

The gas control valve has detected

1

Turn the power off for 10-20 seconds then on again to

 

 

excessive water temperature in the

 

 

 

clear these error codes.

 

 

tank and has activated the ECO

 

 

 

 

 

 

 

(energy cut off) high temperature

2

Replace the gas control valve if the error code persists.

 

 

 

 

limit.

 

 

 

 

 

 

The gas control valve has detected

1

Press and release both temperature adjust buttons

 

 

 

several times - cycle water heater power off and on.

 

 

that one or both of the temperature

 

 

 

 

 

 

 

adjust buttons are stuck.

2

Replace the gas control valve if the error code persists.

 

 

 

 

 

 

 

The gas control valve has detected

1

Turn the power off for 10-20 seconds then on again to

 

 

the water temperature sensor

 

 

 

clear these error codes.

 

 

(located in the control valve's

 

 

 

 

 

 

 

immersion probe) is either open or

2

Replace the gas control valve if the error code persists.

 

 

 

 

shorted.

 

 

 

 

 

 

 

1

Ensure all FV sensor wiring is correct and the igniter

 

 

The gas control valve has detected

 

assembly plug and socket connections on the bottom

 

 

 

 

 

the FV (flammable vapor) sensor is

 

of the gas control valve are making good contact.

 

 

either open or shorted.

2

Replace the FV sensor.

 

 

 

 

 

 

 

 

1

Do not touch any electrical switch, do not use any

 

 

 

 

phone in your building, and do not try to light any

 

 

 

 

appliance.

 

 

 

2

Smell around the water heater to ensure there are no

 

 

 

 

gas leaks at the gas control valve, in the supply gas

 

 

 

 

line(s), or any other type of flammable vapor(s) in the

 

 

The gas control valve has detected

 

area.

 

 

 

 

 

 

the presence of flammable vapors

3

Carefully inspect the area surrounding the water heater

 

 

from the FV (flammable vapor)

 

 

 

for any substances such as gasoline, paint, paint

 

 

sensor.

 

 

 

 

thinners, varnish, or cleaners that could emit flammable

 

 

 

 

 

 

 

 

vapors. Remove anything that can potentially emit

 

 

 

 

flammable vapors from the area and store it properly in

 

 

 

 

a different location.

 

 

 

4

Call the technical information support phone number

 

 

 

 

shown on the water heater labeling for further

 

 

 

 

assistance.

 

 

 

1

On models equipped with a dilution air intake screen on

 

 

The gas control valve has detected

 

the blower assembly - check/clean this screen.

 

 

the air pressure switch circuit is

 

 

 

 

opening repeatedly during one

2

On models equipped with a combustion air intake

 

 

 

 

heating cycle.

 

screen on the base ring (bottom) of the water heater -

 

 

LDO (Lint, Dust, and Oil) lockout

 

check/clean the screen.

 

 

 

 

 

 

 

 

 

condition.

3

Ensure intake air screen(s) on models so equipped are

 

 

 

 

not obstructed.

31

Image 31
Contents 153.332070 153.332040153.332050 153.332060Important Definitions Safe INSTALLATION, USE and ServiceSafety Precautions Table of Contents Customer Responsibilities Product SpecificationsKeep Clear of ALL Obstructions Materials and Basic Tools Needed Natural HOT Surface Igniter & Main Burner Typical InstallationPropane HOT Surface Igniter & Main Burner Removing the Old Water Heater Installation InstructionsFacts to Consider about the Location Cause death, serious bodily injury, or property damage Insulation BlanketsALL AIR from Inside Buildings See Hotter Water can Scald Water PipingValve and Pipe Insulation if supplied GAS Piping Filling the Water Heater Blower Assembly InstallationSequence of Installation Sediment TrapsPage Maximum Vent Lengths Vent Connections to Blower AssemblyVenting and Installation CondensationVenting Vent Terminal InstallationVertical Vent Through Roof Vertical Vent Termination RestrictionsRecommended BRUSH* Size for Primer Cement Applications Vent Pipe PreparationStep G Step BStep E Step FOperating Instructions For Your Safety Read Before LightingTemperature Setting Temperature RegulationThermal Expansion Start UP ConditionsCondensate SMOKE/ODORVenting System Inspection Operational ConditionsBurner Operation and Inspection Housekeeping TEMPERATURE-PRESSURE Relief Valve OperationAnode ROD Inspection Service Drain Valve Washer ReplacementDraining Leakage Checkpoints Blower may run continuously LED Status Problem SolutionBlower may not start in this ConditionTroubleshooting Guidelines Troubleshooting Guidelines This is a Repair Parts LIST, not a Packing List Burner Assembly Outer Door AlternateModel Numbers Part Description Page Page Sears Installation Service Year Limited Warranty on Water HeaterYear Exclusive Kenmore Labor Warranty Warranty Service