Siemens HD2528U, HD2525U Test the Installation, 8A. Test Electric Ignition, Flame Characteristics

Page 10

Step 8: Test the Installation

Installation Preparation Safety Instructions

8A. Test Electric Ignition

Turn on power at breaker.

CAUTION:

If the display flashes and beeps, the polarity of the wiring may be reversed. Reversed polarity can damage the range and can result in electrical shock hazard. Immediately switch off power at the breaker and return to Step 6.

Select a rangetop burner knob. Push down and turn to the flame symbol. If the ignitor/spark module is operating correctly, it will produce a clicking sound. Once the air has been purged from the supply lines, the burner should light within four (4) seconds. After burner lights, turn knob to the off position.

Test each rangetop burner in this fashion.

Call Siemens Service 866-447-4363 if any of the burners do not light.

Some yellow streaking is normal during the initial start-up.

Allow unit to operate 4-5 minutes and re- evaluate before making adjustments.

Flame Characteristics

Yellow Flames:

Further adjustment is required.

Yellow Tips on Outer Cones:

Normal for LP Gas.

Soft Blue Flames:

Normal for Natural Gas.

8B. Test/Adjust Flame

High Setting:

The combustion quality of the flame for each burner must be visually inspected. For propane, the flame should be blue with yellow tips. For natural gas, it should be soft blue in color. The flame should carry over, or surround, the entire burner and should not lift or blow off the burner.

To inspect, turn the burner on. See Figure 14 for appropriate flame characteristics.

If the flame is completely or mostly yellow, verify that the regulator is set for the correct fuel. After adjustment, retest. If any of the burners continue to burn mostly or completely yellow, call Siemens Service 866-447-4363.

Note: With LP use, some yellow tipping on outer cones is normal.

Low Setting:

All burners must also be inspected for carry-over. On low, the flame should completely surround the burner. If any of the cooktop burners do not carry over on the low setting, call Siemens Service 866-447-4363.

Installation is complete at this time.

WHEN PROPERLY ADJUSTED:

There should be a flame at each burner port. There should be no air gap between the flame and burner

Final Steps

Service

Figure 13

Replacement Parts: Visit your Siemens dealer for replacement parts. For a dealer near you contact Siemens Service 866-447-4363.

Image 10
Contents Siemens Dual-Fuel Range With threeD Surround Convection Page Table of Contents Preparation Installation Final Steps ServiceRange Tipping Hazard Service Important Safety InstructionsSafety Instructions Preparation Installation Final Steps Installation Preparation Safety InstructionsTips TIP Install Strain ReliefPrepare Electrical Connection Model HDS, HDConnect the Range Cord Three Wire Connection Installation Final StepsInstallation Connect Electric Proceed to , nextRigid Pipe Method see , this Installation Connect Gas SupplyFlexible Connector Method see , this Test for Gas Leaks8B. Test/Adjust Flame Test the InstallationFlame Characteristics When Properly AdjustedBefore Calling Service Product Data PlatePage Avertissement Table des matièresPièces Fournies Pièces NécessairesPréparation Instructions de sécurité Service Étapes finales InstallationRemarque pour installation à haute altitude Instructions DE Sécurité ImportantesSécurité électrique Sécurité relative aux équipements à gazÉtapes 1 à 4 Préparation Installation de la ventilationInstallation de la fixation antibascule Préparation des armoiresSécurité Étapes finales ServiceInstructions de Étape 5 Préparation de la connexion électriqueInstructions de sécurité Service Étapes finales Installation PréparationÉtape 6 Installation connexion électrique Connexion du cordon de la cuisinière Connexion à 3 filsDébit de gaz à l’appareil Instructions de sécurité Préparation InstallationÉtape 7 Installation connexion de l’alimentation en gaz Passer à «Test de fuite de gaz», colonne suivanteInstallation Préparation Instructions de sécurité Service Étapes finalesPlaque signalétique Avant d’effectuer un appel de servicePlaque signalétique Page Contenido SeguridadPreparación Instalación Pasos FInales Servicio LEA Y Guarde Estas Instrucciones Antes DE Usar Este AparatoInstrucciones Importantes DE Seguridad Advertencia Pasos Finales ServicioCuidado Seguridad Preparación Instalación Instrucciones Importantes DE SeguridadPreparación Seguridad Instalación Pasos Finales Servicio Consejo Instalación Pasos FInales ServicioPaso 5 Preparar la Conexión Eléctrica Modelo HDS, HDConexión con Tres Hilos Conexión con Cuatro Hilos Preferido a tres hilosVerificar Fugas de Gas Seguridad PreparaciónPaso 7 Instalación Conectar el Suministro de Gas Flujo de Gas a la EstufaPaso 8 Probar la Instalación Instalación Preparación Seguridad FinalesPasos Características de las LlamasPlaca con datos del pro-ducto Seguridad Preparación Instalación Pasos FInales ServicioAntes de llamar al servicio Abra el cajón para verla
Related manuals
Manual 52 pages 52.85 Kb

HD2528U, HD2525U specifications

Siemens has established itself as a leader in the home appliances sector, and among its latest offerings are the HD2528U and HD2525U models. These innovative devices are designed to enhance food preparation experiences in modern kitchens, focusing on efficiency, versatility, and user-friendly technology.

The Siemens HD2528U features a powerful motor with a robust 1500-watt output, providing users with the ability to handle even the toughest ingredients with ease. It is equipped with various speed settings, allowing for precision control over blending and mixing processes. This model also includes a turbo function, which delivers an extra burst of power for quick blending tasks, ensuring seamless transitions from chopping to pureeing.

On the other hand, the HD2525U model is slightly more compact but does not compromise on performance. It offers a 1200-watt motor that efficiently caters to everyday kitchen tasks. With a focus on functionality, it also boasts multiple speed settings, which are perfect for adapting to different food types and preparing a variety of dishes. Both models include a pulse function, providing additional control and ensuring that ingredients can be blended to the preferred consistency.

One of the standout features of the Siemens HD2528U and HD2525U is their advanced technology. The devices are engineered with high-quality stainless steel blades that are not only durable but are also designed to achieve optimal blending results. The ergonomic design ensures comfortable handling, reducing strain during extended use. Additionally, the safety features in both models include a safety lock mechanism that prevents operation when the lid is not properly secured.

Another important aspect of these appliances is their ease of cleaning. The removable and dishwasher-safe parts make maintenance straightforward, catering to the fast-paced lifestyle of modern users. This thoughtfulness in design extends beyond functionality; both models exhibit an elegant, contemporary aesthetic that seamlessly integrates into any kitchen decor.

In summary, the Siemens HD2528U and HD2525U stand out in the crowded market of kitchen appliances due to their powerful motors, multiple speed settings, ergonomic design, and user-centric safety features. With a focus on both performance and convenience, these blenders are perfect for anyone looking to elevate their culinary skills and streamline their food preparation processes. Whether you’re an avid home cook or just looking to simplify daily meal prep, Siemens’ latest offerings promise to deliver the quality and efficiency expected from this renowned brand.