Siemens HD2525U, HD2528U Prepare Electrical Connection, Tip, Model HDS, HD, Install Strain Relief

Page 7

Step 5: Prepare Electrical Connection

5. Prepare Electrical Connection

Ranges are dual rated for use on either 120/240 VAC or 120/208 VAC. See chart below for power ratings and circuit breaker sizes based on the supply voltage for each model.

MODEL HDS, HD

 

 

VOLTS

HZ

RATING

CIRCUIT

A.C.

 

KW

BREAKER

120/240

60

6.5

30 AMPS

120/208

60

4.8

30 AMPS

Install Strain Relief

Place strain relief in knockout below terminal block (See Figure 4). Feed range cord through hole and strain relief up to terminal block. Allow for slack in the cord between the strain relief and terminal block. Once cord length/ slack has been adjusted, attach strain relief per instructrions included with strain relief.

WARNING

The strain relief provided with your range cord must be properly installed.

Safety Instructions

CAUTION:

Make certain that gas shutoff valve and all burner controls are in the OFF position before beginning

Verify that wiring to house is adequate. Contact your local utility company to verify that the present electric service to your home is adequate. In some instances, the size of the wiring to the house and service switch must be increased to handle the electrical load demanded by the range.

Verify that wiring inside house is adequate. Most wiring codes require a separate circuit with separate disconnect switch and fuses either in the main entrance panel or in a separate switch and fuse box. The range requires a three wire 120/240 or 120/208 volt, 30 AMP, 60 Hz AC circuit.

Most local building regulations and codes require that electrical wiring be done by licensed electricians. Be sure to install your range according to the electric codes in place in your region.

To prevent electrical shock, the grounding prong on the range cord should not be cut or removed under any circumstances. It must be plugged into a matching grounding type receptacle and connected to a correctly polarized 240- Volt circuit. If there is any doubt as to whether the wall receptacle is properly grounded, have it checked by a qualified electrician.

General Information

Siemens recommends that the range be installed with a power cord set (not supplied)*. The electrical rating of the power cord set must be 120/240 volt, 30 amperes minimum. The power cord set shall be marked “For Use with Ranges.” Always use a new power cord.

Note: In Canada, the range is shipped from the factory with the range cord already installed. Proceed to “Step 7: Installation - Connect the Gas Supply)

For installations other than those in Canada, connect the range cord at the terminal block (See next page for detailed instructions). Access the terminal block by removing the cover in the lower right hand corner of the range back panel (See Figure 4). Install the strain relief (see next column) and the proper connector through the knockout(s) provided. The electrical supply, including flexible conduit or power cord, should be restricted to the shaded areas in Figure 2 (previous page)

*Not needed for Canadian installations

TIP

The knockout panel (below the terminal block can be removed from the range to install the strain relief: Remove panel from range, install strain relief in panel and re-attach. DO NOT remove entire range back panel.

Electric Connection

 

(found behind terminal

 

block cover)

Feed

 

 

Range

 

Cord

 

Through

 

Strain

 

Relief in

 

Knockout

 

Panel

 

Here

Gas Connection

 

Figure 4

WARNING

Risk of Electric Shock or Fire. Frame grounded to neutral through a ground strap. Grounding through the neutral conductor is prohibited for new branch- circuit installations (1996 NEC), mobile homes, and recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor. For installations where grounding through the neutral conductor is prohibited, (a) disconnect the link from the neutral, (b) use grounding terminal or lead to ground unit, (c) connect neutral terminal to lead branch circuit neutral in usual manner (when the appliance is to be connected by means of a cord kit, use 4-conductor cord for this purpose).

Use only cord kits rated 125/250 volts (minimum), 30 amperes and labeled “For Use with Ranges”. Strain relief provided with cord must be installed per instructions included with cord.

Figure 5

Preparation Installation

Final Steps Service

English • 5

Image 7
Contents Siemens Dual-Fuel Range With threeD Surround Convection Page Table of Contents Preparation Installation Final Steps ServiceRange Tipping Hazard Important Safety Instructions ServiceSafety Instructions Preparation Installation Final Steps Installation Preparation Safety InstructionsTips Model HDS, HD Install Strain ReliefPrepare Electrical Connection TIPProceed to , next Installation Final StepsInstallation Connect Electric Connect the Range Cord Three Wire ConnectionTest for Gas Leaks Installation Connect Gas SupplyFlexible Connector Method see , this Rigid Pipe Method see , thisWhen Properly Adjusted Test the InstallationFlame Characteristics 8B. Test/Adjust FlameProduct Data Plate Before Calling ServicePage Pièces Nécessaires Table des matièresPièces Fournies AvertissementInstructions DE Sécurité Importantes Service Étapes finales InstallationRemarque pour installation à haute altitude Préparation Instructions de sécuritéSécurité relative aux équipements à gaz Sécurité électriquePréparation des armoires Installation de la ventilationInstallation de la fixation antibascule Étapes 1 à 4 PréparationÉtape 5 Préparation de la connexion électrique Étapes finales ServiceInstructions de SécuritéConnexion du cordon de la cuisinière Connexion à 3 fils Service Étapes finales Installation PréparationÉtape 6 Installation connexion électrique Instructions de sécuritéPasser à «Test de fuite de gaz», colonne suivante Instructions de sécurité Préparation InstallationÉtape 7 Installation connexion de l’alimentation en gaz Débit de gaz à l’appareilService Étapes finales Installation Préparation Instructions de sécuritéPlaque signalétique Avant d’effectuer un appel de servicePlaque signalétique Page LEA Y Guarde Estas Instrucciones Antes DE Usar Este Aparato SeguridadPreparación Instalación Pasos FInales Servicio ContenidoInstrucciones Importantes DE Seguridad Advertencia Pasos Finales ServicioCuidado Instrucciones Importantes DE Seguridad Seguridad Preparación InstalaciónPreparación Seguridad Instalación Pasos Finales Servicio Modelo HDS, HD Instalación Pasos FInales ServicioPaso 5 Preparar la Conexión Eléctrica ConsejoConexión con Cuatro Hilos Preferido a tres hilos Conexión con Tres HilosFlujo de Gas a la Estufa Seguridad PreparaciónPaso 7 Instalación Conectar el Suministro de Gas Verificar Fugas de GasCaracterísticas de las Llamas Instalación Preparación Seguridad FinalesPasos Paso 8 Probar la InstalaciónAbra el cajón para verla Seguridad Preparación Instalación Pasos FInales ServicioAntes de llamar al servicio Placa con datos del pro-ducto
Related manuals
Manual 52 pages 52.85 Kb

HD2528U, HD2525U specifications

Siemens has established itself as a leader in the home appliances sector, and among its latest offerings are the HD2528U and HD2525U models. These innovative devices are designed to enhance food preparation experiences in modern kitchens, focusing on efficiency, versatility, and user-friendly technology.

The Siemens HD2528U features a powerful motor with a robust 1500-watt output, providing users with the ability to handle even the toughest ingredients with ease. It is equipped with various speed settings, allowing for precision control over blending and mixing processes. This model also includes a turbo function, which delivers an extra burst of power for quick blending tasks, ensuring seamless transitions from chopping to pureeing.

On the other hand, the HD2525U model is slightly more compact but does not compromise on performance. It offers a 1200-watt motor that efficiently caters to everyday kitchen tasks. With a focus on functionality, it also boasts multiple speed settings, which are perfect for adapting to different food types and preparing a variety of dishes. Both models include a pulse function, providing additional control and ensuring that ingredients can be blended to the preferred consistency.

One of the standout features of the Siemens HD2528U and HD2525U is their advanced technology. The devices are engineered with high-quality stainless steel blades that are not only durable but are also designed to achieve optimal blending results. The ergonomic design ensures comfortable handling, reducing strain during extended use. Additionally, the safety features in both models include a safety lock mechanism that prevents operation when the lid is not properly secured.

Another important aspect of these appliances is their ease of cleaning. The removable and dishwasher-safe parts make maintenance straightforward, catering to the fast-paced lifestyle of modern users. This thoughtfulness in design extends beyond functionality; both models exhibit an elegant, contemporary aesthetic that seamlessly integrates into any kitchen decor.

In summary, the Siemens HD2528U and HD2525U stand out in the crowded market of kitchen appliances due to their powerful motors, multiple speed settings, ergonomic design, and user-centric safety features. With a focus on both performance and convenience, these blenders are perfect for anyone looking to elevate their culinary skills and streamline their food preparation processes. Whether you’re an avid home cook or just looking to simplify daily meal prep, Siemens’ latest offerings promise to deliver the quality and efficiency expected from this renowned brand.