Siemens HD2525U, HD2528U Installation Connect Gas Supply, Flexible Connector Method see , this

Page 9

Step 7: Installation - Connect Gas Supply

Important note for LP users: The appliance is shipped from the factory for use with natural gas. It must be converted for use with propane. A qualified technician or installer must do the conversion.

The gas connection is located below the back panel of the range (See Figure 4, Page 4). It is accessible through the warming drawer access panel or from the back of the range. To reach access panel, remove warming drawer. Shut off main gas supply valve before disconnecting the old range and leave it off until the new hook-up has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on.

The range can be installed using rigid pipe or a CSA International-certified flexible metal appliance connector. If using a flexible connector, always use a new connector. Apply pipe joint compound orTeflon* tape appropriate for use with LP gas and Natural gas around all male pipe threads to prevent leaks.

If not already present, install gas shut off valve in an easily accessible location. Make sure all users know where and how to shut off the gas supply to the range.

Note: The installer should inform the consumer of the location of the gas shut-off valve.

Flexible Connector Method (see Figure 11, this page)

1.Install male 1/2” flare adaptor at the 1/2” NPT internal thread of the range inlet. Use a backup wrench on the elbow fitting to avoid damage.

2.Install male 1/2” or 3/4” flare union adapter on the NPT internal thread of the manual shut-off valve.

3.Connect flexible metal appliance connector.

4.Make sure circuit breaker is off and then plug range cord in to electrical outlet.

5.Push range back into position insuring that range leg slides under the anti-tip bracket. The range will sit 3/4” away from the wall when properly installed.

Note: Be careful not to crimp flexible connector!

6.Carefully tip range forward to insure that anti-tip bracket engages and prevents tip-over.

Rigid Pipe Method (see Figure 12, this page)

The configuration of the rigid pipe connection will vary depending on the location of the gas pipe stub. Refer to Figure 12 for details.

1.Make sure circuit breaker is off and then plug range cord in to electrical outlet.

2.Push range back into position insuring that range leg slides under the anti-tip bracket. The range will sit 3/4” away from the wall when properly installed.

3.Carefully tip range forward to insure that anti-tip bracket engages and prevents tip-over.

4.Connect pipe to range at union. Access the connection through the access panel behind the warming drawer.

Note: Be careful not to apply pressure to warming drawer element during rigid pipe installation.

Proceed to “Test for Gas Leaks”, next column.

Test for Gas Leaks

Leak testing is to be conducted by the installer according to the instructions given in this section.

Turn on Gas. Apply a non-corrosive leak detection fluid to all joints and fittings in the gas connection between the shut-off valve and the range. Include gas fittings and joints in the range if connections were disturbed during installation. Bubbles appearing around fittings and connections indicate a leak.

If a leak appears, turn off supply line gas shut-off valve and tighten connections. Retest for leaks by turning on the supply line gas shut-off valve. When leak check is complete (no bubbles appear), test is complete. Wipe off all detection fluid residue. Proceed to Step 8: Test the Installation.

CAUTION

NEVER CHECK FOR LEAKS WITH A FLAME.

DO NOT CONTINUE TO THE NEXT STEP UNTIL ALL LEAKS ARE ELIMINATED.

CAUTION

Before you plug in an electrical cord, be sure all controls are in the OFF position.

GasShut-Off

Valve

Regulator

Flexible

 

Connector

Figure 11: Flexible Connector Method

elbow

gas shut off valve

 

elbow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

nipple

union

nipple

nipple

 

elbow:

 

connect to

1/2” to 3/4”

regulatorhere

gas pipe

GasFlowtoRange

Figure 12: Rigid Pipe Method

English • 7

Safety Instructions Preparation Installation

Final Steps Service

Image 9
Contents Siemens Dual-Fuel Range With threeD Surround Convection Page Preparation Installation Final Steps Service Table of ContentsRange Tipping Hazard Important Safety Instructions ServiceSafety Instructions Preparation Installation Installation Preparation Safety Instructions Final StepsTips Prepare Electrical Connection Install Strain ReliefTIP Model HDS, HDInstallation Connect Electric Installation Final StepsConnect the Range Cord Three Wire Connection Proceed to , nextFlexible Connector Method see , this Installation Connect Gas SupplyRigid Pipe Method see , this Test for Gas LeaksFlame Characteristics Test the Installation8B. Test/Adjust Flame When Properly AdjustedProduct Data Plate Before Calling ServicePage Pièces Fournies Table des matièresAvertissement Pièces NécessairesRemarque pour installation à haute altitude Service Étapes finales InstallationPréparation Instructions de sécurité Instructions DE Sécurité ImportantesSécurité relative aux équipements à gaz Sécurité électriqueInstallation de la fixation antibascule Installation de la ventilationÉtapes 1 à 4 Préparation Préparation des armoiresInstructions de Étapes finales ServiceSécurité Étape 5 Préparation de la connexion électriqueÉtape 6 Installation connexion électrique Service Étapes finales Installation PréparationInstructions de sécurité Connexion du cordon de la cuisinière Connexion à 3 filsÉtape 7 Installation connexion de l’alimentation en gaz Instructions de sécurité Préparation InstallationDébit de gaz à l’appareil Passer à «Test de fuite de gaz», colonne suivanteService Étapes finales Installation Préparation Instructions de sécuritéAvant d’effectuer un appel de service Plaque signalétiquePlaque signalétique Page Preparación Instalación Pasos FInales Servicio SeguridadContenido LEA Y Guarde Estas Instrucciones Antes DE Usar Este AparatoPasos Finales Servicio Instrucciones Importantes DE Seguridad AdvertenciaCuidado Instrucciones Importantes DE Seguridad Seguridad Preparación InstalaciónPreparación Seguridad Instalación Pasos Finales Servicio Paso 5 Preparar la Conexión Eléctrica Instalación Pasos FInales ServicioConsejo Modelo HDS, HDConexión con Cuatro Hilos Preferido a tres hilos Conexión con Tres HilosPaso 7 Instalación Conectar el Suministro de Gas Seguridad PreparaciónVerificar Fugas de Gas Flujo de Gas a la EstufaPasos Instalación Preparación Seguridad FinalesPaso 8 Probar la Instalación Características de las LlamasAntes de llamar al servicio Seguridad Preparación Instalación Pasos FInales ServicioPlaca con datos del pro-ducto Abra el cajón para verla
Related manuals
Manual 52 pages 52.85 Kb

HD2528U, HD2525U specifications

Siemens has established itself as a leader in the home appliances sector, and among its latest offerings are the HD2528U and HD2525U models. These innovative devices are designed to enhance food preparation experiences in modern kitchens, focusing on efficiency, versatility, and user-friendly technology.

The Siemens HD2528U features a powerful motor with a robust 1500-watt output, providing users with the ability to handle even the toughest ingredients with ease. It is equipped with various speed settings, allowing for precision control over blending and mixing processes. This model also includes a turbo function, which delivers an extra burst of power for quick blending tasks, ensuring seamless transitions from chopping to pureeing.

On the other hand, the HD2525U model is slightly more compact but does not compromise on performance. It offers a 1200-watt motor that efficiently caters to everyday kitchen tasks. With a focus on functionality, it also boasts multiple speed settings, which are perfect for adapting to different food types and preparing a variety of dishes. Both models include a pulse function, providing additional control and ensuring that ingredients can be blended to the preferred consistency.

One of the standout features of the Siemens HD2528U and HD2525U is their advanced technology. The devices are engineered with high-quality stainless steel blades that are not only durable but are also designed to achieve optimal blending results. The ergonomic design ensures comfortable handling, reducing strain during extended use. Additionally, the safety features in both models include a safety lock mechanism that prevents operation when the lid is not properly secured.

Another important aspect of these appliances is their ease of cleaning. The removable and dishwasher-safe parts make maintenance straightforward, catering to the fast-paced lifestyle of modern users. This thoughtfulness in design extends beyond functionality; both models exhibit an elegant, contemporary aesthetic that seamlessly integrates into any kitchen decor.

In summary, the Siemens HD2528U and HD2525U stand out in the crowded market of kitchen appliances due to their powerful motors, multiple speed settings, ergonomic design, and user-centric safety features. With a focus on both performance and convenience, these blenders are perfect for anyone looking to elevate their culinary skills and streamline their food preparation processes. Whether you’re an avid home cook or just looking to simplify daily meal prep, Siemens’ latest offerings promise to deliver the quality and efficiency expected from this renowned brand.