Pioneer RS-D7R, RS-P90 Checklist, Installation / Troubleshooting, Symptom Cause Remedy

Page 61

Troubleshooting

When an error occurs, locate the cause according to the list below. In most cases, the prob- lem is incorrect connections or settings.

1.Double check the connections and settings using the checklist.

2.If connections and settings are correct, press the RESET button.

Refer to “Resetting the microprocessor” on page 10.

3.If the malfunction continues even after pressing the RESET button, contact your dealer or nearest authorized Pioneer Service Station.

Checklist

Symptom	Cause	Remedy	Page
No Operation	The battery is not	Connect the battery.	-------
	connected.

	An clear/red lead is not	Connect all clear/red leads	56
	properly connected.	to the battery terminal,	58
		supplied with constant
		power, regardless of the
		ignition switch position
		after running them through
		the vehicle’s fuse unit.

	A clear/black lead (ground)	Firmly connect all the	56
	is not properly connected.	clear/black leads to	58
		the vehicle (metal) body.

	A blue/white lead is not	Connect the blue/white	56
	properly connected.	lead of the RCA input power	57
		amplifier to the blue/white
		lead of this unit.

	The fuse is blown.	Remove the cause and	56
		replace with another fuse
		of the same rating.

	Incorrect connection.	Make sure all the	56~58
		connectors are properly
		connected.

Installation / Troubleshooting

61

61

ENG/MASTER 96

Image 61

Contents RS-P90 Contents Display for the Person who Set Up Key Finder Remote control RS-D7RHead unit RS-D7R Closed state Open stateRemote control Menu display Opening and closing the remote control coverKey Finder When the cover is open When the cover is closedWhen the cover is closed in the middle of operation Menu display in closed stateKey Finder / Before Using This Product Before Using This ProductAbout this unit Case of trouble About this manualProduct registration About the digital network Before Using This ProductRemove the covering Resetting the microprocessorSwitching to the audio menu Audio AdjustmentAudio menu Balance adjustment FAD/BAL Control Closed state Audio Adjustment MainSwitching to the main menu Main menuBass/treble adjustment B/T Open state Press the Function button To select the setting Using the compression CP Open stateUsing the position selector Posi Adjusting the listening position PS Open stateButton Position Experimenting with other positionsUse the position selector function and select the position Fine tuning the positionPoints concerning fine tuning Time alignment adjustment function of the network menu Relation to time alignment adjustment functionIncrease or decrease the level with the 5/∞ buttons Source level adjustment SLA Open stateAbout the equalizer menu Audio Adjustment EqualizerBand graphic equalizer 31B-GEQ Band parametric equalizer 3B-PEQEqualizer menu Switching to the equalizer menuRelation between frequency characteristics and sound quality Points when adjusting the equalizer curve Switch between right and left to set up the equalizer curve Adjusting the 31 band graphic equalizer Fine Open stateWhen completing the adjustment About the adjustment using the parametric equalizer Adjusting the 3 band parametric equalizer Fine Open stateSeparate 3 band adjustment for left/right Select functionSetting the equalizer curve Switch between left and right to set up the equalizer curve Adjust other bandsCommon to 31B-GEQ and 3B-PEQ Flat function FLT Open stateClear function CLR Open state What is the multi-amp system? Audio Adjustment NetworkTo cancel the network menu, press the Band button Switching to the network menuAudio Adjustment Network Network menu N.WSwitching to the time alignment adjustment mode Time alignment adjustment T.A. Open stateMeasuring the distance to be corrected Delay Time Unit of distance must be centimeters NetworkPress Function buttons 1 or 2 and select the band to input Inputting the distance to be corrected Delay TimeAudio Adjustment Network Range Cut-off frequency Level adjustment H.P.F L.P.F Filter adjustment FTR Open stateUsing the mute function MUT Switching to the filter adjustment modeAbout the H.P.F. and L.P.F About the slopeAdjusting the filter Press Function button 3 and adjust the slope of each filter Press the 5/∞ buttons Adjust the level of each bandPress Function button 4 and adjust the phase of each band Switch between left and right channel to adjust the filterFor better frequency characteristics Important points in adjusting the slopeAdjusting the subwoofer effectively Adjusting the low-range effectivelyMinimum delay phase characteristics Minimum phase MIP Linear phase characteristics Linear phase LINMemory functions of adjusted audio menu Memo Audio Adjustment Memory FunctionsBase memory Custom memoryAudio Adjustment Memory Function Switching to memory modeEqualizer menu Network menuAdjust each audio menu Storing the adjustment data in memorySwitch to the memory mode of each menu refer to Press the Shift button to cancel memory modeRecalling data stored in memory Close the cover of the remote controlForward/reverse order Functions of equalizer menu Specifying the memory number directlyPress the Function button to recall the memory Specifying the memory number directlyMemory recall operations on the equalizer menu Memory protect function When turning the protect function ON/OFFRecall the memory refer to Inputting characters Switching to the edit mode Display for the Person who Set Up the Audio AdjustmentsPress the Menu button to switch to the audio menu Inputting the nameSwitch the desired character type with Function button When removing the car battery Equalizer Memory Data MemoNetwork Filter characteristics Memory Data Memo Network Time alignmentConnecting the Units Using the corrugated tube Setting exampleConnecting the Units Routing the optical cableRS-D7R Connection diagramConnecting the RCA input amplifier Connecting the leads Connecting the power terminalAttach the cable clamp Secure the optical cableInstalling the unit InstallationInstall the brackets to the bottom of the unit Install the unit to the vehicleChecklist TroubleshootingInstallation / Troubleshooting Symptom Cause RemedyGeneral SpecificationsSpecifications Pioneer Corporation