Pioneer RS-D7R, RS-P90 owner manual Press the 5/∞ buttons Adjust the level of each band

Page 39

Important points in adjusting cut-off frequencies

•If the subwoofer is installed in the rear tray, setting a high cut-off frequency of L.P.F. of the subwoofer separates the bass and gives the listener the feeling that the bass is coming from behind. The L.P.F. of the subwoofer is recommended to be set at 100 Hz or below.

•Speakers used for mid and high-ranges are generally constructed to handle a limited level of input compared to low range speakers. If the cut-off frequency of H.P.F. is set lower than necessary, strong bass signals can reach the speaker and may damage it.

Important points in adjusting the level

•The low band, because of its sound frequency characteristics, incorporates the basic frequencies of many musical instruments. It is recommended that the level adjustment of the low band be made first, and then the level adjustment of the mid, high, and subwoofer be made in that order.

8.Press the 5/∞ buttons and

adjust the level of each band.

Holding down these buttons continues their operations.

Switch to each band and adjust the level in order to create a better overall balance.

9.Press FUNCTION button 3 and adjust the slope of each filter.

Press the button to change the adjustment values.

The slope can be set up for either the high pass filter or the low pass filter. When setting up, have in mind the adjustments to be made to the next band.

10.Press FUNCTION button 4 and adjust the phase of each band.

Press the button to change between normal (NOR) and reverse (REV). Set up the one which makes the better link to the next band.

11.Switch between left and right channel to adjust the filter.

Repeat steps 4 to 10 to adjust the filters of left and right.

39

Audio Adjustment <Network>

39

ENG/MASTER 96

Image 39

Contents RS-P90 Contents Display for the Person who Set Up Closed state Open state Remote control RS-D7RKey Finder Head unit RS-D7ROpening and closing the remote control cover Remote control Menu displayKey Finder Menu display in closed state When the cover is closedWhen the cover is open When the cover is closed in the middle of operationBefore Using This Product Key Finder / Before Using This ProductAbout this unit About this manual Case of troubleProduct registration About the digital network Before Using This ProductRemove the covering Resetting the microprocessorAudio Adjustment Switching to the audio menuAudio menu Main menu Audio Adjustment MainBalance adjustment FAD/BAL Control Closed state Switching to the main menuBass/treble adjustment B/T Open state Press the Function button To select the setting Using the compression CP Open stateExperimenting with other positions Adjusting the listening position PS Open stateUsing the position selector Posi Button PositionUse the position selector function and select the position Fine tuning the positionPoints concerning fine tuning Time alignment adjustment function of the network menu Relation to time alignment adjustment functionIncrease or decrease the level with the 5/∞ buttons Source level adjustment SLA Open stateBand parametric equalizer 3B-PEQ Audio Adjustment EqualizerAbout the equalizer menu Band graphic equalizer 31B-GEQEqualizer menu Switching to the equalizer menuRelation between frequency characteristics and sound quality Points when adjusting the equalizer curve Adjusting the 31 band graphic equalizer Fine Open state Switch between right and left to set up the equalizer curveWhen completing the adjustment Select function Adjusting the 3 band parametric equalizer Fine Open stateAbout the adjustment using the parametric equalizer Separate 3 band adjustment for left/rightSetting the equalizer curve Switch between left and right to set up the equalizer curve Adjust other bandsCommon to 31B-GEQ and 3B-PEQ Flat function FLT Open stateClear function CLR Open state What is the multi-amp system? Audio Adjustment NetworkNetwork menu N.W Switching to the network menuTo cancel the network menu, press the Band button Audio Adjustment NetworkTime alignment adjustment T.A. Open state Switching to the time alignment adjustment modeMeasuring the distance to be corrected Delay Time Unit of distance must be centimeters NetworkPress Function buttons 1 or 2 and select the band to input Inputting the distance to be corrected Delay TimeAudio Adjustment Network Range Cut-off frequency Level adjustment H.P.F L.P.F Filter adjustment FTR Open stateAbout the slope Switching to the filter adjustment modeUsing the mute function MUT About the H.P.F. and L.P.FAdjusting the filter Switch between left and right channel to adjust the filter Press the 5/∞ buttons Adjust the level of each bandPress Function button 3 and adjust the slope of each filter Press Function button 4 and adjust the phase of each bandAdjusting the low-range effectively Important points in adjusting the slopeFor better frequency characteristics Adjusting the subwoofer effectivelyMinimum delay phase characteristics Minimum phase MIP Linear phase characteristics Linear phase LINCustom memory Audio Adjustment Memory FunctionsMemory functions of adjusted audio menu Memo Base memoryNetwork menu Switching to memory modeAudio Adjustment Memory Function Equalizer menuPress the Shift button to cancel memory mode Storing the adjustment data in memoryAdjust each audio menu Switch to the memory mode of each menu refer toSpecifying the memory number directly Close the cover of the remote controlRecalling data stored in memory Forward/reverse order Functions of equalizer menuSpecifying the memory number directly Press the Function button to recall the memoryMemory recall operations on the equalizer menu When turning the protect function ON/OFF Memory protect functionRecall the memory refer to Inputting the name Display for the Person who Set Up the Audio AdjustmentsInputting characters Switching to the edit mode Press the Menu button to switch to the audio menuSwitch the desired character type with Function button When removing the car battery Equalizer Memory Data MemoNetwork Filter characteristics Memory Data Memo Network Time alignmentConnecting the Units Routing the optical cable Setting exampleUsing the corrugated tube Connecting the UnitsRS-D7R Connection diagramConnecting the RCA input amplifier Connecting the leads Connecting the power terminalAttach the cable clamp Secure the optical cableInstall the unit to the vehicle InstallationInstalling the unit Install the brackets to the bottom of the unitSymptom Cause Remedy TroubleshootingChecklist Installation / TroubleshootingGeneral SpecificationsSpecifications Pioneer Corporation