Pioneer RS-P90 Installation, Installing the unit, Install the brackets to the bottom of the unit

Page 60

Installation

Note:

•Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly.

•Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunction.

•Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

•Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

Installing the unit

1.Install the brackets to the bottom of the unit.

The brackets may also be installed vertically.

Screw (3 mm ⋅ 6 mm)

Bracket

2. Install the unit to the vehicle.

Tapping screw (3 mm ⋅ 8 mm)

Car mat or chassis

Drill a hole of 1.5 mm to 2 mm

ENG/MASTER 96

Image 60

Contents RS-P90 Contents Display for the Person who Set Up Remote control RS-D7R Key FinderHead unit RS-D7R Closed state Open stateOpening and closing the remote control cover Remote control Menu displayKey Finder When the cover is closed When the cover is openWhen the cover is closed in the middle of operation Menu display in closed stateBefore Using This Product Key Finder / Before Using This ProductAbout this unit About this manual Case of troubleProduct registration Before Using This Product About the digital networkResetting the microprocessor Remove the coveringAudio Adjustment Switching to the audio menuAudio menu Audio Adjustment Main Balance adjustment FAD/BAL Control Closed stateSwitching to the main menu Main menuBass/treble adjustment B/T Open state Using the compression CP Open state Press the Function button To select the settingAdjusting the listening position PS Open state Using the position selector PosiButton Position Experimenting with other positionsFine tuning the position Use the position selector function and select the positionPoints concerning fine tuning Relation to time alignment adjustment function Time alignment adjustment function of the network menuSource level adjustment SLA Open state Increase or decrease the level with the 5/∞ buttonsAudio Adjustment Equalizer About the equalizer menuBand graphic equalizer 31B-GEQ Band parametric equalizer 3B-PEQSwitching to the equalizer menu Equalizer menuRelation between frequency characteristics and sound quality Points when adjusting the equalizer curve Adjusting the 31 band graphic equalizer Fine Open state Switch between right and left to set up the equalizer curveWhen completing the adjustment Adjusting the 3 band parametric equalizer Fine Open state About the adjustment using the parametric equalizerSeparate 3 band adjustment for left/right Select functionSetting the equalizer curve Adjust other bands Switch between left and right to set up the equalizer curveFlat function FLT Open state Common to 31B-GEQ and 3B-PEQClear function CLR Open state Audio Adjustment Network What is the multi-amp system?Switching to the network menu To cancel the network menu, press the Band buttonAudio Adjustment Network Network menu N.WTime alignment adjustment T.A. Open state Switching to the time alignment adjustment modeMeasuring the distance to be corrected Delay Time Network Unit of distance must be centimetersInputting the distance to be corrected Delay Time Press Function buttons 1 or 2 and select the band to inputAudio Adjustment Network Filter adjustment FTR Open state Range Cut-off frequency Level adjustment H.P.F L.P.FSwitching to the filter adjustment mode Using the mute function MUTAbout the H.P.F. and L.P.F About the slopeAdjusting the filter Press the 5/∞ buttons Adjust the level of each band Press Function button 3 and adjust the slope of each filterPress Function button 4 and adjust the phase of each band Switch between left and right channel to adjust the filterImportant points in adjusting the slope For better frequency characteristicsAdjusting the subwoofer effectively Adjusting the low-range effectivelyLinear phase characteristics Linear phase LIN Minimum delay phase characteristics Minimum phase MIPAudio Adjustment Memory Functions Memory functions of adjusted audio menu MemoBase memory Custom memorySwitching to memory mode Audio Adjustment Memory FunctionEqualizer menu Network menuStoring the adjustment data in memory Adjust each audio menuSwitch to the memory mode of each menu refer to Press the Shift button to cancel memory modeClose the cover of the remote control Recalling data stored in memoryForward/reverse order Functions of equalizer menu Specifying the memory number directlySpecifying the memory number directly Press the Function button to recall the memoryMemory recall operations on the equalizer menu When turning the protect function ON/OFF Memory protect functionRecall the memory refer to Display for the Person who Set Up the Audio Adjustments Inputting characters Switching to the edit modePress the Menu button to switch to the audio menu Inputting the nameSwitch the desired character type with Function button When removing the car battery Memory Data Memo EqualizerNetwork Filter characteristics Network Time alignment Memory Data MemoConnecting the Units Setting example Using the corrugated tubeConnecting the Units Routing the optical cableConnection diagram RS-D7RConnecting the RCA input amplifier Connecting the power terminal Connecting the leadsSecure the optical cable Attach the cable clampInstallation Installing the unitInstall the brackets to the bottom of the unit Install the unit to the vehicleTroubleshooting ChecklistInstallation / Troubleshooting Symptom Cause RemedySpecifications GeneralSpecifications Pioneer Corporation