Pioneer RS-P90, RS-D7R owner manual Inputting the distance to be corrected Delay Time

Page 34

Audio Adjustment <Network>

Inputting the distance to be corrected (Delay Time)

Scope of adjustment: 0 cm to 192.5 cm (0.77 cm/1 step) (S.W.: 0 cm to 385 cm (1.54 cm/1 step))

1.Open the cover of the remote control in the network menu (refer to page 5).

This switches to network menu setting screen.

2.Press the FUNCTION button 2.

The display switches to time alignment adjustment screen, allowing time alignment adjustment.

3.Press the FUNCTION button 6 and select the driver’s seat (posi- tion).

Press the buttons to switch between “FRONT-R” and “FRONT-L”. Select the position when measuring the distance to be corrected as shown on the page 33.

Note:

•The correct distance can not be input unless these operations are conducted.

4.Press FUNCTION buttons 3 or 5 and select the speaker channel to input.

Press the buttons to switch between left

(L) and right (R).

5.Press FUNCTION buttons 1 or 2 and select the band to input.

Each press of the FUNCTION buttons 1 or 2 select the desired band in the following order:

S.W. (ultrabass-range) Ô LOW (low-range) Ô MID (mid-range) Ô HIGH (high- range)

34

34

ENG/MASTER 96

Image 34

Contents RS-P90 Contents Display for the Person who Set Up Head unit RS-D7R Remote control RS-D7RKey Finder Closed state Open stateRemote control Menu display Opening and closing the remote control coverKey Finder When the cover is closed in the middle of operation When the cover is closedWhen the cover is open Menu display in closed stateKey Finder / Before Using This Product Before Using This ProductAbout this unit Case of trouble About this manualProduct registration Before Using This Product About the digital networkResetting the microprocessor Remove the coveringSwitching to the audio menu Audio AdjustmentAudio menu Switching to the main menu Audio Adjustment MainBalance adjustment FAD/BAL Control Closed state Main menuBass/treble adjustment B/T Open state Using the compression CP Open state Press the Function button To select the settingButton Position Adjusting the listening position PS Open stateUsing the position selector Posi Experimenting with other positionsFine tuning the position Use the position selector function and select the positionPoints concerning fine tuning Relation to time alignment adjustment function Time alignment adjustment function of the network menuSource level adjustment SLA Open state Increase or decrease the level with the 5/∞ buttonsBand graphic equalizer 31B-GEQ Audio Adjustment EqualizerAbout the equalizer menu Band parametric equalizer 3B-PEQSwitching to the equalizer menu Equalizer menuRelation between frequency characteristics and sound quality Points when adjusting the equalizer curve Switch between right and left to set up the equalizer curve Adjusting the 31 band graphic equalizer Fine Open stateWhen completing the adjustment Separate 3 band adjustment for left/right Adjusting the 3 band parametric equalizer Fine Open stateAbout the adjustment using the parametric equalizer Select functionSetting the equalizer curve Adjust other bands Switch between left and right to set up the equalizer curveFlat function FLT Open state Common to 31B-GEQ and 3B-PEQClear function CLR Open state Audio Adjustment Network What is the multi-amp system?Audio Adjustment Network Switching to the network menuTo cancel the network menu, press the Band button Network menu N.WSwitching to the time alignment adjustment mode Time alignment adjustment T.A. Open stateMeasuring the distance to be corrected Delay Time Network Unit of distance must be centimetersInputting the distance to be corrected Delay Time Press Function buttons 1 or 2 and select the band to inputAudio Adjustment Network Filter adjustment FTR Open state Range Cut-off frequency Level adjustment H.P.F L.P.FAbout the H.P.F. and L.P.F Switching to the filter adjustment modeUsing the mute function MUT About the slopeAdjusting the filter Press Function button 4 and adjust the phase of each band Press the 5/∞ buttons Adjust the level of each bandPress Function button 3 and adjust the slope of each filter Switch between left and right channel to adjust the filterAdjusting the subwoofer effectively Important points in adjusting the slopeFor better frequency characteristics Adjusting the low-range effectivelyLinear phase characteristics Linear phase LIN Minimum delay phase characteristics Minimum phase MIPBase memory Audio Adjustment Memory FunctionsMemory functions of adjusted audio menu Memo Custom memoryEqualizer menu Switching to memory modeAudio Adjustment Memory Function Network menuSwitch to the memory mode of each menu refer to Storing the adjustment data in memoryAdjust each audio menu Press the Shift button to cancel memory modeForward/reverse order Functions of equalizer menu Close the cover of the remote controlRecalling data stored in memory Specifying the memory number directlyPress the Function button to recall the memory Specifying the memory number directlyMemory recall operations on the equalizer menu Memory protect function When turning the protect function ON/OFFRecall the memory refer to Press the Menu button to switch to the audio menu Display for the Person who Set Up the Audio AdjustmentsInputting characters Switching to the edit mode Inputting the nameSwitch the desired character type with Function button When removing the car battery Memory Data Memo EqualizerNetwork Filter characteristics Network Time alignment Memory Data MemoConnecting the Units Connecting the Units Setting exampleUsing the corrugated tube Routing the optical cableConnection diagram RS-D7RConnecting the RCA input amplifier Connecting the power terminal Connecting the leadsSecure the optical cable Attach the cable clampInstall the brackets to the bottom of the unit InstallationInstalling the unit Install the unit to the vehicleInstallation / Troubleshooting TroubleshootingChecklist Symptom Cause RemedySpecifications GeneralSpecifications Pioneer Corporation