Pioneer AVIC-90DVD installation manual Connecting the System

Page 6

Connecting the System

CAUTION

Pioneer does not recommend that you install or service your DVD navigation unit yourself. Installing or servicing of the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your navigation unit to authorized Pioneer service personnel.

Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed.

Do not drill a hole into the engine compartment to connect the yellow lead of the unit to the car battery. Engine vibration may eventually cause the insula- tion to fail at the point where the wire passes from the passenger compart- ment into the engine compartment. Take extra care in securing the wire at this point.

It is extremely dangerous to allow the GPS antenna lead or microphone lead to become wound around the steering column or shift lever. Be sure to install the unit in such a way that it will not obstruct driving.

Make sure that wires will not interfere with moving parts of the car, such as the shift lever, parking brake or seat sliding mechanism.

Do not route wires where they will be exposed to high temperatures. If the insulation heats up, wires may become damaged, resulting in a short circuit or malfunction.

Do not cut the GPS antenna lead to shorten it or use an extension to make it longer. Altering the antenna cable could result in a short circuit or malfunc- tion.

Do not shorten any leads. If you do, the protection circuit may fail to work properly.

Never feed power to other electronic products by cutting the insulation of the power supply lead of the DVD navigation unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

5

Image 6
Contents Installation Manual Important Information Contents Important Safeguards English Español Deutsch Français Italiano Nederlands Connecting the System To prevent damage Before installing the unitPower cord Connector Parts suppliedConnecting the system When resetting AV Head UnitConnecting to the display with 20-pin RGB input Connecting the System To Video input Connecting the power cord Needle-nosed pliers Ground side Parking brake switchClamp firmly with needle-nosed pliers Close the cover Nect it Backup lamp lead in the trunkThis is connected so that the navigation system can Fuse resistorYellow Installation Before installing and fixing Before using the adhesive tapeTo guard against electromagnetic interference Installing the main unit Installation notesMain unit Installation direction lever Locking screwFit mounting angles to the sides of the main unit Fix to the floor with tapping screws Floor Tapping screwFastening the unit to the factory radio mounting bracket Installing the GPS antenna DashboardRoof Rear shelf GPS antenna Metal sheet Clamp 5 pcs When routing the lead in from inside the trunk When installing the antenna outside the car on the bodyWhen routing the lead in from the top of the door Make a U-shaped loop in the lead ClampsRemote controller Alkaline battery Holder Installing the Remote controllerRemote controller handling notes Loading the batteriesRemote Controller When installing with double-sided tapeRemote Controller Holder Double-sided tape largeInstalling the microphone Microphone Microphone clipClamp When installing the microphone on the sun visor Install the microphone on the microphone clipInstall the microphone clip on the sun visor When installing the microphone on the steering column Install the microphone clip on the steering columnReset button Reconnecting the batteryStart the engine Press the reset button on the main unit Set the navigation systemInformation Importante Remarques sur l’installation Pièces fournies Branchement du système dans le cas d’unPour protéger le système de navigation Importantes Mesures DE Securite English Français Deutsch Français Italiano Nederlands Branchement du système Pièces fournies Avant de raccorder l’appareilPour éviter des dégâts Position ACC Pas de position ACCBranchement du système Ce produitSortie audio Cordon d’alimentation Cf. pages Commande de niveauAfin d’obtenir les informations sur le trafic Sortie vidéoSortie audio Sortie vidéo Vert Microphone Cf. Câble RCA vendu séparément Antenne GPSÉcran muni de prises d’entrée Cinch RCA Branchement du cordon d’alimentation Fermez le couvercleTion de chacun et effectuez les raccorde Les câbles de ce produit et ceux d’autresMême couleur bien que remplissant la Tion de chaque câbleJaune Installation Avant un branchement définitif Avant d’employer le ruban adhésifInstallation de l’unité principale Remarques sur l’installationUnité principale Levier du sens d’installation Vis de verrouillage Sous l’unité de navigation DVDRouillage Installation Fixez l’unité sur le plancher avec les vis taraudeuses Vis taraudeuse PlancherDe diamètre Installation Installation de l’antenne GPS Planche de bord Toit Capot du coffre Lunette arrièreAntenne GPS Plaque métallique Serre-fils 5 pièces Cheminement du câble sur le haut de la portière Cheminement du fil par l’intérieur du coffreTélécommande Pile alcaline Support Installation de la télécommandeRemarques sur le maniement de la télécommande Insertion des pilesEn cas dinstallation avec bande adhésive double face Boîtier de télécommandeRetirer Bande adhésive double face large Installation du microphone Fixez l’attache du microphone sur le pare-soleil Installation du microphone sur le pare-soleilFixez le microphone sur l’attache fournie Microphone AttacheInstallation du microphone sur la colonne de direction Fixez l’attache du microphone sur la colonne de directionBande adhésive double face Configurez le système de navigation automobile Branchement de la batterieTouche de réinitialisation Page Page Pioneer Corporation
Related manuals
Manual 82 pages 34.94 Kb