JVC TM-H1950CG HOW to USE the Menu Functions, Front panel Function Contents Button Displayed

HOW TO USE THE MENU FUNCTIONS

DISPLAY AND SELECTION IN THE <MENU> SCREEN MODE (SETTING)

You can set the following menu items.

Set them depending on your needs.

• APERTURE	• COLOR SYSTEM
• ADJ. BAR POSI.	• COMPO. LEVEL*
• COLOR TEMP.	• RUSH DELAY

1. Press the MENU button.

MENU	The <MENU> screen is displayed.
	* The on-screen display goes off automatically after about five
	minutes with operation performed.

<MENU> screen

1< MENU >

	4	APERTURE		: 00
		ADJ. BAR POSI.		: LOWER
		COLOR TEMP.		: 6500
		COLOR SYSTEM		: AUTO
		COMP. LEVEL		: 00
2		RUSH DELAY		:	STD.	3
				4
			EXIT

2.Press the CHROMA/PHASE or CONTRAST/BRIGHT button to select MENU items.

CHROMA CONTRAST	VOLUME/SELECT	MENU
PHASE BRIGHT

CHROMA CONTRAST

PHASE BRIGHT

APERTURE

ADJ. BAR POSI.

COLOR TEMP.

COLOR SYSTEM

COMPO. LEVEL*

RUSH DELAY

A selection mark (4) is put next to the selected item.

Front panel	Function	Contents
button	displayed
CHROMA/		Forward selection mark (4)
PHASE
CONTRAST/		Reverse selection mark (4)
BRIGHT

<Front panel buttons>

1Selection mark (4): Indicates the

menu item you select.

2Menu item: Menu items you can select.

3Setting display: Indicates the current

settings (value).

4Function display: The functions of the front panel buttons (5 buttons on the left) correspond to the function displayed.

3. Press the VOLUME/SELECT buttons to set.

VOLUME/SELECT

Front panel

Function

Contents

button

displayed

VOLUME/

+

Increase (to max. value)

SELECT (+)

4

Forward the setting value

VOLUME/

–

Decrease (to min. value)

SELECT (–)

1

Reverse the setting value

Menu items

Purpose

Setting range

APERTURE

Picture aperture level

00

+01

• • • • • • • • • • • •

+39

+40

ADJ.BAR POSI

Volume bar position

LOWER

UPPER

COLOR TEMP.

Color temperature of white

6500

9300

balance

COLOR SYSTEM

Color system

AUTO

NTSC

AUTO

PAL

COMPO. LEVEL*

Component level

– 40

– 39

• •– 01

00 +1 • • +9

+10

RUSH DELAY

Delay time

STD.

SLOW

*For normal use, leave the COLOR SYSTEM setting to AUTO.

If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).

*COMPO. LEVEL is displayed only with component serial digital (SDI) input. (Shown with INPUT-C and INPUT-D except for RGB input.)

4.If you want to set the other menu items, repeat procedures 2 and 3.

5.Press the MENU button to quit.

MENU	Front panel	Function	Contents
	button	displayed
	MENU	EXIT	Quit (or Release) the <MENU>
			screen

Function	Contents
displayed
	Forward the menu item.
	Reverse the menu item.
–	Lower the adjustment
	value. (to the minimum)
+	Raise the adjustment
	value. (to the maximum)
4	Forward the setting value.
1	Reverse the setting value.
EXIT	Exits the <MENU> screen.

Note:

●RUSH DELAY sets the delay between the time the power switch is pressed and the time power is actually supplied to the monitor’s circuits. STD. : Power turns on approximately

1 second after the power switch is pressed.

SLOW : Power turns on approximately 3 seconds after the power switch is pressed.

*When turning on multiple Color- Video Monitors simultaneously, it is recommended to use STD. or SLOW settings to reduce the rush current of the entire system.

12