Blank Skip Activation, Scan Times | Blaupunkt CM147 specification

section. Use << and >> to choose minimum amount of blank time before blank skip begins from between 1 to 16 seconds. SUGGESTION: Classical music listeners may want to specify a longer blank, so that the unit doesn’t mistake soft passages for blank spots.

Blank Skip Activation

Press << or >> to turn Blankskip on or off.

Scan Times

You can set different scan times for Radio (“RD SCNTM”), Cassette (“TP SCNTM”), and Changer (“CD SCNTM”) between 1 and 16 seconds. Press << or >> to adjust scan time.

Confirmation Beep On/Off (“BTTNBEEP”)

To activate or defeat beep for all button presses, press << or >>. (Button presses requiring more than 1/2 second always have confirmation beep.)

Adjustable Mute Level (“MUTE LVL”)

The unit’s mute level can be adjusted to any volume level. This mute level also applies to cellular mute. During Menu mode, once “MUTE LVL” appears, actual mute level is heard. Adjust the mute level volume by using <</>>, NOT + and –. (If mute is activated when unit volume level is lower than mute level, unit volume level is maintained, even though “MUTE” appears.

Maximum Turn-On Volume Level (“MAXONVOL”)

Sets maximum volume that is heard when unit is turned on. (Once “MAXONVOL” appears, actual MAXONVOL level is heard.) Adjust the MAXONVOL volume by using <</>>, NOT + and –. If unit is turned off while volume is louder than MAXONVOL, turn-on volume will be at MAXONVOL level. However, if unit is turned off when volume level is lower than MAXONVOL, turn-on volume will be at level it was when unit was turned off.

Loudness Levels

You can choose between two loudness settings for each audio source: “LOUD TAPE”, “LOUD AUX”, “LOUD CD”, (for CD Changer) “LOUD AM” and “LOUD FM”. “LOUD 1” provides up to 8 dB boost in bass (centered at 60 Hz) and up to a 2 dB boost in treble (centered at 8 KHz). “LOUD 2” provides up to 12 dB boost in bass (centered at 60 Hz) and up to a 4 dB boost in treble (centered at 8 KHz). To set the loudness level for each source, use << and >>.

Radio Station Naming (“STN NAME”)

Available only while radio is active source. One name per frequency, 8 characters per name. (Names can be assigned to any frequency, preset or not.) If you try to enter more than 30 names, “**FULL**” appears. You can then enter new names after erasing some of existing names.

To store station names:

1.Press DIS for more than 2 seconds to enter Menu mode.

2.Scroll to Radio Station Naming feature by pressing /\ / V .

3.Enter Station Name Access mode by pressing << or >> button.

4.Tune to desired station using AM, FM, presets or /\ / V buttons. If previously named, name appears.

5.Press << or >> buttons to enter Station Name Edit mode.

6.Press /\ / V to select character. Select “__“ for a blank space.

7.Press << or >> buttons to select next character position.

8.Press Mute to store name. Display blinks STORING twice before return to Station Access mode.

9.To name another station, repeat steps 4-8.

10.To return to Menu, press Mute again.

(There is no time-out from Station Name Access & Edit modes.)

Display Priority & Radio Station Names- See Display Options on page 13.

Changing a Radio Station Name

Repeat steps 1 to 10 in Radio Station Naming, changing only those characters that you wish to change.

Erasing ONE Radio Station Name

Access Station Access mode (See Radio Station Naming, above.) Choose station with name to be deleted. When name appears, press Mute for 2 seconds. Beep sounds. Release now to delete this name. “NAME” and “DELETED” blink alternately.