Blaupunkt RCM 104 A Setting the time in the DSC menu, Adjusting the TIM standby mode/TIM time

Page 17

When pressing TIM once again, you will hear the message text recorded until that interrup- tion.

Setting the time in the DSC menu:

TIM needs the exact time in order to operate precisely. The time also has to be re-adjusted after every interruption of the power supply.

Press DSC and the time will be display- ed.

Press << to set the hours or >> to ad- just the minutes.

The corresponding value is flashing. To change the setting,

press the rocker button /. To confirm your entry,

press -dBor DSC.

When pressing the -dB button, you can go on working in the DSC menu immediately.

Adjusting the TIM standby mode/TIM time

The TIM-TIME to be set corresponds to the planned departure time. TIM will then be active 1.5 hours before and after this adju- sted time, so that the traffic messages will be recorded during a period of three hours.

Note: During this period, a motor antenna will remain extracted. Please take into account the warning note of the end of this chapter.

 

 

 

adjusted

 

 

 

 

start

TIM-TIME

 

end

 

 

1.5 hours

 

 

1.5 hours

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The motor antenna will be extracted

Use the rocker button / to choose TIM-TIME in the DSC menu.

Press << or >> to call up the adjusted time.

If TIM OFF is displayed, the TIM function is deactivated.

Use the rocker button / to set the time.

Use << to move to the hours or >> to adjust the minutes.

Confirm your entry by

pressing -dBor DSC.

The TIM-TIME is stored.

TIM will be active 1.5 hours before and after the adjusted TIM-TIME.

Also, TIM will automatically stay on standby for three hours after the radio was turned off. When TIM is activated, the display will briefly show “TIM ON” when the set is switched off.

Deactivating the TIM standby mode

Press DSC with the radio being turned on.

Use the / rocker button to select the item TIM TIME.

Press -dBand switch to TIM OFF with rocker button / (you find this item between the time settings for 23:00 and 0:00).

When TIM OFF is flashing,

press DSC or -dB.

If the motor antenna is retracted immediately after selecting TIM OFF, you can be assured that the TIM function is deactivated.

Note:

If the TIM function is not used for a longer period of time, we recommend you to switch it off in order to avoid that the battery goes flat.

Warning

The motor antenna could be damaged in a car wash.

If you have a motor antenna installed, it will remain extracted after you have turned off the radio with the TIM function being activa- ted. The antenna may also be extracted in the car wash when the set is turned off and the TIM function activated.

40

Image 17
Contents Barcelona RCM 104 a 15 14 Table of contents Switching off Switching onQuick instructions FMTAF Mode DSC ModeCPS AUDTIM/TA 3, 4, 5, 6 preset buttonsScan ? BC Dolby BC NR@ Eject button Press Cassette loading slot To change the seek tuning sensitivi- ty Press loTape side selector MIXInstallation/connection Traffic safetyImportant notes What you really have to readOptical indication of theft protection KeyCardNever try to pull out the KeyCard by force Replacing a KeyCardADA on/off antenna test RDS Radio Data SystemAF Alternative Frequency Stereo mono switch FM Adjusting the seek tuning sensi- tivityREG Regional Selecting the wavebandChanging the memory bank FM Preset scanningStoring stations Recalling stored stationsProgram types Scanning stations with Radio ScanPTY Program Type PTY priority Tuning into a station with PTYReception of traffic announcements with RDS-EON Switching the warning beep offEnhanced Other Networks Traffic announcement priority on/offTraffic Memo TIM Automatic seek tuning startAdjusting the traffic message volume Adjusting the TIM standby mode/TIM time Setting the time in the DSC menuDeactivating the TIM standby mode Motor antenna could be damaged in a car washIf you are sure Do not switch on the radio until you have left the car washRT Radiotext Tape operation Winding with RM Radio Monitor Tions with BLS Blank SkipDolby BC NR Listening to the radio during fast Time DSC programmingADA TestCD name specified with NameCDC Name Time Playback timeTo quit the DSC mode and store the set- ting Using SRC of the car radio Switching the CD mode onMIX CD MIX MAGDeleting CD names Entering/displaying CD namesVivaldi DSC CD DispAppendix Survey of DSC default settingsTechnical data Blaupunkt-Werke GmbH