Blaupunkt RCM 104 A Quick instructions, Switching on, Switching off, Fmt, Extra function

Page 4

Quick instructions

1Switching on:

Press the ON button (the KeyCard has to be inserted), the set plays with the pre-adjusted volume.

Switching off:

Press ON for approximately 1 second. If the set was turned on by pressing ON, the KeyCard can be used for swit- ching the system on and off. Please read the information of chapter “Key- Card”.

The set may also be turned off via the vehicle’s ignition (provided that it was connected correspondingly). After the ignition was switched off, a double beep tone reminds you that you should remove the KeyCard before leaving your vehicle.

To operate the set when the ignition is switched off (KeyCard is inserted), pro- ceed as follows:

Press “ON” after the double beep tone. The set will be turned on.

To avoid that the battery goes flat, the system will be turned off automatically after a playback time of one hour.

2To change the volume: Press VOL+/VOL-.

Each time the set is switched on, it will play with the pre-adjusted volume (VOL FIX). You may also change the VOL FIX setting (see chapter “DSC pro- gramming“).

3FMT

Press this button to switch between the memory banks I, II, and T (Travelstore). As soon as this button is pressed, the system will automatically switch to FM.

Extra function:

Store the six most powerful stations automatically with Travelstore: Press FMT until seek tuning starts in the display.

4M•L

To change between medium wave (MW) and long wave (LW) frequencies.

5-dB- for instantly changing the volume. Press the -dBbutton to instantly mute the audio source. The display will then show MUTE. Return to normal volume by pressing either the -dBor the VOL+ button.

When pressing VOL-, the normal play- back volume is identical to the -dB(mu- ted) volume.

To program the mute volume, proceed as follows:

•Adjust the desired volume.

•Press -dBfor approximately 2 se- conds (beep tone is released).

This volume will then be stored as the mute volume.

Extra function:

Press this button to store the values set in the DSC menu.

DEUTSCH

ENGLISH

PORTUGUES ESPAGÑOL SVENSKA NEDERLAND ITALIANO FRANÇAIS

27

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Barcelona RCM 104 a 15 14 Table of contents Switching on Switching offQuick instructions FMTDSC Mode AF ModeCPS AUD3, 4, 5, 6 preset buttons TIM/TAScan ? BC Dolby BC NRTo change the seek tuning sensitivi- ty Press lo @ Eject button Press Cassette loading slotTape side selector MIXTraffic safety Installation/connectionImportant notes What you really have to readKeyCard Optical indication of theft protectionNever try to pull out the KeyCard by force Replacing a KeyCardAF Alternative Frequency RDS Radio Data SystemADA on/off antenna test Adjusting the seek tuning sensi- tivity Stereo mono switch FMREG Regional Selecting the wavebandPreset scanning Changing the memory bank FMStoring stations Recalling stored stationsPTY Program Type Scanning stations with Radio ScanProgram types Tuning into a station with PTY PTY prioritySwitching the warning beep off Reception of traffic announcements with RDS-EONEnhanced Other Networks Traffic announcement priority on/offAdjusting the traffic message volume Automatic seek tuning startTraffic Memo TIM Setting the time in the DSC menu Adjusting the TIM standby mode/TIM timeDeactivating the TIM standby mode Motor antenna could be damaged in a car washRT Radiotext Do not switch on the radio until you have left the car washIf you are sure Tape operation Dolby BC NR Listening to the radio during fast Tions with BLS Blank SkipWinding with RM Radio Monitor DSC programming TimeADA TestName CD name specified withCDC Name Time Playback timeTo quit the DSC mode and store the set- ting Switching the CD mode on Using SRC of the car radioMIX CD MIX MAGEntering/displaying CD names Deleting CD namesVivaldi DSC CD DispTechnical data Survey of DSC default settingsAppendix Blaupunkt-Werke GmbH
Top Page Image Contents