Blaupunkt SEATTLE RDM 169 operating instructions Scanning stored stations with Preset Scan

Page 20
If “lo” is displayed, the radio will only pick up strong, local stations (low sensitivity).
Changing the scan time
The scan time can be set from between five to a maximum of 30 seconds.
Please refer to the section on “DSC pro- gramming - SCANTIME”.
Selecting the seek tuning sensi- tivity
You can alter the automatic seek tuning sensitivity.
If you do not select a station, the scan func- tion will automatically switch off after the fre- quency band has been run through com- pletely. The unit will tune into the station you were listening to before you started the scan function.

Radio operation with RDS (Radio Data System)

• by pressing ST1 - ST6.

To select a scanned station and switch

To select a scanned station and switch

To select a station on a different waveband:

off Preset Scan:

off the Radio Scan function:

• Press NEXT as often as necessary un-

• Press SCA or the rocker switch briefly.

• Press SCA or the rocker switch briefly.

til the desired memory bank appears

 

 

and then select the station by pressing

 

 

ST1 - ST6.

 

 

ENGLISH DEUTSCH

Scanning stored stations with Preset Scan

You can have all of the stored stations briefly scanned on all wavebands and in the se- lected FM memory bank.

Scanning stations with Radio Scan

ITALIANO FRANÇAIS

Preset Scan cannot be started unless PTY

You can also scan all of the stations within

is switched off (“PTY” is not highlighted in

reception range.

the display).

Radio Scan cannot be started unless PTY

If necessary, switch off PTY on menu level

is switched off (“PTY” is not highlighted in

2. To do so

the display).

• press TU and switch off the function by

If necessary, switch off PTY on menu level

pressing the corresponding key.

2. To do so

To start Preset Scan:

• press TU and switch off the function by

• Press SCA for approx. 1 second.

pressing the corresponding key.

 

NEDERLANDS SVENSKA

All of the stored stations on the waveband

To start the Scan function:

 

selected and within reception range will be

• Press SCA briefly.

If “lo” does not light up, the radio will also

scanned one after the other. “SCAN” and

All of the stations on the waveband select-

pick up weaker, more distant stations (high

the station name or frequency will flash al-

ed and within reception range will be

sensitivity).

ternately in the display.

scanned one after the other. “SCAN” and

If you want to alter the sensitivity level,

 

the station name or frequency will flash al-

please refer to the section on “DSC program-

 

ternately in the display.

ming - LO/DX”).

ESPAÑOL PORTUGUÊS

57

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Alabama DJ Seattle RDM Tokyo RDM 13 12 Table of contents Quick Reference Quick Reference Next FMNext AM MW, LW BNDMIX ExitPTY CLR Rocker switch Radio operationRPT Repeat DSC-MODE PTY AUDDIS DisplayCDC = TU TunerRC 08 remote control unit V+ Volume control SRC SourceRadio operation Station seek tuning up Select trackImportant notes KeyCard theft protection system Putting the unit into operationRemoving the KeyCard Training a second KeyCardKeyCard theft protection system Short Additional MemoryTurn On Message T.O.M Displaying the radio pass dataCare of your KeyCard Lost or damaged KeyCardTraining the new KeyCard Making mistakes in the entrySelecting the operating Optimising display Mode Legibility REG regional program Radio operation with RDS Radio Data SystemAF Alternative frequency Station tuning Radio operation with RDS Radio Data SystemSelecting a waveband Scrolling through the broadcast- ing networks FM onlyStoring stations Changing the memory bank FMRecalling stored stations Scanning stored stations with Preset Scan Scanning stations with Radio ScanSwitching from stereo to mono Automatic bandwidth adjust- ment SharxPTY Program Type Program typeChecking the program type of the sta- tion Displaying the selected program typeSelecting a program type Storing program typesScanning stations with PTY Scan PTY prioritySwitching the warning beep off Traffic information station reception with RDS-EONTraffic announcement priority On/offSwitching on CD operation Switching on CD changer opera- tionCD operation / CD changer operation Inserting a CDSelecting the display mode CD operation / CD changer operationSelecting CDs and titles Repeating tracks/CDsMIX CD MIX OFFTo stop the Scan function Entering CD namesDeleting CD names/TPM with Setting the clock Correcting the clock after the power has been disconnectedClock Time Displaying the clockSetting the equaliser Setting the equaliser Assistance in setting your equaliserDSC programming CD Name Sharx Hicut12/24H Mode DSC programmingSTEREO/MONO CLK AUTO/MANTo quit the DSC programming mode and store the adjustment Peak ON/OFFDSC programming Specifications Overview of the DSC factory set- tingsAmplifier TunerREG Glossary Technical TerminologyMute Softkey Software key Glossary Technical TerminologyScan Index CODE-ERRIndex Scan CDBlaupunkt-Werke GmbH
Top Page Image Contents