Blaupunkt SEATTLE RDM 169 KeyCard theft protection system, Short Additional Memory

Page 14

KeyCard theft protection system

• Remove the first KeyCard and insert

Short Additional Memory

the new one while “CHANGE” still ap-

(S.A.M.)

pears in the display.

The second KeyCard available from your

After the display indicates “READY” or

specialised dealer allows you to read out

“LEARN KC”,

short information, which will run through the

• press DSC.

display, such as, for example, the phone

Now you can also use the new KeyCard for

number of your car dealer or the emergen-

operating your unit.

cy call number of your automobile associa-

A maximum of two cards can be used with

tion.

the set.

The freely selectable text with a maximum

If you attempt “train” a third one, the access

of 162 characters can be programmed by

authorisation for the KeyCard not used for

any dealer who has the required equipment

the “training” process will be deleted auto-

available.

matically.

Turn On Message (T.O.M.)

Displaying the radio pass data

The second KeyCard available from your

 

You can use the KeyCard supplied with your

specialised dealer also allows you to dis-

set to display the radio pass data such as

play a special turn-on message each time

the model name, product number (7 6 ...)

the radio is switched on.

and serial number.

The freely selectable text with a maximum

Please refer to the section on “DSC pro- of 48 characters can be programmed by any

gramming - READ KC”.

dealer who has the required equipment

 

available.

 

Each time you turn on your system with the

 

second KeyCard, the programmed text will

 

appear in the display.

Optical display as theft protec- tion

Flashing light diode ?

When the vehicle is stationary and the Key- Card has been removed, the light diode can be switched to flash for extra anti-theft se- curity.

For this it is necessary that the positive pow- er supply line and the permanent +12 V lead are connected such as described in the in- stallation instructions.

Make sure that the unit is switched off; the operating panel is unlocked; the KeyCard has been removed; “LED ON” has been selected in the DSC mode (factory setting). If necessary, please refer to the section on “DSC programming - LED”.

Switching off the flashing light

The flashing light can be switched off by selecting “LED OFF” in the DSC menu.

DEUTSCH ENGLISH FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL PORTUGUÊS

51

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Alabama DJ Seattle RDM Tokyo RDM 13 12 Table of contents Quick Reference Next AM MW, LW Quick ReferenceNext FM BNDMIX ExitPTY CLR Rocker switch Radio operationRPT Repeat DSC-MODE PTY AUDDIS DisplayCDC = TU TunerRadio operation Station seek tuning up RC 08 remote control unitV+ Volume control SRC Source Select trackImportant notes Removing the KeyCard KeyCard theft protection systemPutting the unit into operation Training a second KeyCardTurn On Message T.O.M KeyCard theft protection systemShort Additional Memory Displaying the radio pass dataTraining the new KeyCard Care of your KeyCardLost or damaged KeyCard Making mistakes in the entrySelecting the operating Optimising display Mode Legibility REG regional program Radio operation with RDS Radio Data SystemAF Alternative frequency Selecting a waveband Station tuningRadio operation with RDS Radio Data System Scrolling through the broadcast- ing networks FM onlyStoring stations Changing the memory bank FMRecalling stored stations Scanning stored stations with Preset Scan Scanning stations with Radio ScanPTY Program Type Switching from stereo to monoAutomatic bandwidth adjust- ment Sharx Program typeSelecting a program type Checking the program type of the sta- tionDisplaying the selected program type Storing program typesScanning stations with PTY Scan PTY priorityTraffic announcement priority Switching the warning beep offTraffic information station reception with RDS-EON On/offCD operation / CD changer operation Switching on CD operationSwitching on CD changer opera- tion Inserting a CDSelecting CDs and titles Selecting the display modeCD operation / CD changer operation Repeating tracks/CDsMIX CD MIX OFFTo stop the Scan function Entering CD namesDeleting CD names/TPM with Clock Time Setting the clockCorrecting the clock after the power has been disconnected Displaying the clockSetting the equaliser Setting the equaliser Assistance in setting your equaliserDSC programming CD Name Sharx HicutSTEREO/MONO 12/24H ModeDSC programming CLK AUTO/MANTo quit the DSC programming mode and store the adjustment Peak ON/OFFAmplifier DSC programming SpecificationsOverview of the DSC factory set- tings TunerREG Glossary Technical TerminologyMute Softkey Software key Glossary Technical TerminologyScan Index CODE-ERRIndex Scan CDBlaupunkt-Werke GmbH
Top Page Image Contents