Blaupunkt RDM 126 operating instructions Receiving traffic programme stations with RDS-EON, On/off

Page 18

-NDR2 airs a PTY-POP programme.

-The system will switch to the linked station NDR2 for the duration of the “POP” programme.

During CD or CDC operation, the set will also switch to the programme offering the selected PTY within the broadcasting net- work.

After the PTY programme the system will remain in the radio mode.

Notice:

As earlier mentioned, these functions are currently only supported by a limited number of RDS stations.

Receiving traffic programme stations with RDS-EON

The abbreviation “EON” stands for En-

Traffic announcement priority

hanced Other Networks, meaning the

on/off

exchange of information within a radio net-

If the priority for traffic announcement pro-

work.

grammes is activated, “TA” will light up in

Many FM broadcasters offer traffic messag-

the display.

es for their service area at regular intervals.

To switch the priority on or off:

All traffic programme stations transmit a

• Press TIM for approximately two sec-

special carrier signal alongside their pro-

grammes, which is decoded by your car ra-

onds until you hear a beep.

dio. If this signal is identified, “TP” will ap-

When pressing TIM while a message is be-

pear in the display (Traffic Programme).

ing broadcast, this message will be interrup-

In addition to these, there are also stations

ted. The unit will then switch back to the pre-

which do not actually transmit traffic pro-

vious condition, though the recording of this

grammes themselves, but by using RDS-

message in the TIM memory will remain

EON they offer the possibility to receive the

uninterrupted.

traffic messages broadcast by another traf-

If you press the TIM button once again,

fic programme station in the same radio

“RECORD” will appear in the display for

network.

approximately two seconds.

If you wish to have the priority for traffic an-

When interrupting an EON message, the

nouncements activated while listening to

radio will not continue to record the an-

one of these stations (e.g. NDR3), “TA” must

nouncement since it will switch back to the

appear on the display panel.

programme heard before.

If a traffic announcement is broadcast, the

The priority for other traffic messages re-

radio will automatically switch to the linked

mains active.

traffic programme station (in this case,

Please note that several buttons have no

NDR2) for the duration of the message (EON

function while a traffic announcement is

message) and return to the original pro-

broadcast.

gramme (NDR3) afterwards.

 

DEUTSCH ENGLISH FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL PORTUGUÊS

47

Image 18
Contents London RDM 10 11 Contents Quick reference Rocker switch Extra rocker switch functionsAUD D GEO C DSC Mode B PTY SC/MIX MIX OFF MIX CDMIX MAG TPMEject @ 1, 2, 3, 4, 5, 6 preset buttons? SRC SRC source CD slotExtra function GEO GEOAUD Extra function AUDImportant notes Replacing a KeyCard KeyCard theft protection systemRemoving the KeyCard Never pull out the KeyCard directlyTurn On Message T.O.M Switching off the flashlightShort Additional Memory S.A.M Optical indication for extra securityRadio operation with RDS Radio Data System Changing the memory bank FM Manual tuning withScrolling through the broadcast- ing networks only FM Storing stationsOff Preset Scan To start Preset ScanTo select a scanned station and switch Changing the scan timeSwitching from stereo to mono FM Programme typeSport Storing programme types Scanning stations with PTY-SCANPTY priority Receiving traffic programme stations with RDS-EON Traffic announcement priorityOn/off Switching the warning beep off Automatic seek tuning startAdjusting GEO for traffic mes- sages and the warning beep To make a settingProgramming the TIM standby mode / TIM times Traffic Memo TIMWash Mode TIM standby mode while the raDeactivating the TIM standby Recalling stored traffic messagTemporarily interrupting the TIM standby mode Before driving into a car washCD and CDC changer operation optional Switching to CDC operation Selecting the display modeSelecting CDs and titles Storing the display mode Scan operationClearing all CDs from the TPM Entering CD namesClearing a CD from the TPM Clearing a magazine from the TPMCD names with DSC-UPDATE Deleting a CD nameClearing TPM information Speech TimerDSC programming CD/CDC NamePTY Lang ColourLED on Learn KCCD/CDC UPD Overview of the DSC factory settingsTo quit the DSC programming mode and store the adjustment AUXTuner SpecificationsAppendix CD playerBosch Gruppe
Related manuals
Manual 29 pages 4.04 Kb