Viking TMC 148 operating instructions Quick Reference Section

Page 4

Quick Reference Section

1On/off using the switch

When the KeyCard is inserted, press one of the keys shown.

The unit will play at the pre-adjusted volume.

On/off switch using the KeyCard:

The unit switches on or off when you insert or remove the KeyCard.

Note:

Please read the information in the sec- tion on the “KeyCard theft protection system”.

Switching the unit on/off with the ignition:

The unit can be switched on/off with the vehicle ignition if the unit has been installed accordingly.

After you switch off the ignition, you will hear two beeps to remind you to remove the KeyCard before you leave the vehicle.

Switching the unit on when the igni- tion is off

If the ignition is switched off (but the KeyCard is still in place), it is possible to operate the unit as follows:

After the beep press ON. The unit will switch on.

After the unit has played for an hour, it will switch off automatically to prevent the vehicle battery from running down.

2VOL+ / VOL- Adjusting the volume.

When the unit is switched on, it will play at a pre-defined volume (VOL FIX).

VOL FIX can also be adjusted (refer to “DSC programming”).

3 - Mute

Press to lower the volume quickly. “MUTE” will appear in the display. Press or VOL+ to cancel this function.

If you press VOL-, the (mute) volu- me will be set to the regular volume le- vel.

The mute volume can be programmed as follows:

•Adjust the volume to the desired level

• Press for 2 sec. (you will hear a beep).

You have just stored this volume level as the mute volume.

Additional function for

Storage key in the DSC menu.

4SC - Scan Radio mode

Scan

Press SC briefly –

“FM SCAN” will flash in the display, al- ternating with the radio station current- ly being scanned. All of the FM stati- ons within reception range will be scanned.

Preset Scan

Preset Scan cannot be started unless PTY is switched off (“PTY” is not lit in the display.)

Press SC for approx. 2 seconds – you will hear a beep, “Scan” will flash in the display, alternating with the stati- on symbol of the station scanned.

The stations stored on the station pre- set buttons and within reception range will be scanned.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Viking TMC Operating InstructionsPage Contents Quick Reference Section Quick Reference Section AUD B DSC-MODE a PTY@Quick Reference DisplayKeyCard/TMC DriveCard theft protection system Inserting the cardBND MIX Setting the balance left/right and fader front/rear To switch off AUD Press the key brieflyAUD Additional EQU ON/OFF functionImportant notes Important notes GuaranteeInternational telephone informa- tion Operating the unit for the first time KeyCard/TMC DriveCard theft protection systemRemoving the card KeyCard/TMC DriveCard theft protection system AF Alternative frequency Radio operation with RDS Radio Data SystemREG Regional programme Station tuning Radio operation with RDS Radio Data SystemSelecting a waveband Scrolling through the broadcast networks FM onlySwitching between the memory banks FM Scanning stored stations with Preset ScanTo start Preset Scan Storing stationsSelecting the automatic tuning sensitivity Switching from stereo to monoAutomatic bandwidth adjust- ment FM Scanning stations with Radio ScanNews Programme typeWeather Finance Storing programme types Scanning stations with PTY ScanPTY priority Automatic seek tuning start Switching the warning beep offTraffic information station reception with RDS-EON Traffic announcement priority on/offTMC -Traffic Message Channel TMC HelpSelecting a TMC station Traffic information can be selectedTMC -Traffic Message Channel Making a selection for TMCActivating stored areas or roads selection Activating your selectionSwitching TMC on/off TMC traffic informationCD mode Switching to CD modeInserting a CD Removing a CDSetting the clock Correcting the clock after the power has been disconnectedClock Time Displaying the clockSetting the equaliser Setting the equaliser Assistance in setting your equaliserFrequency range Sound impression/problem What to do Bass Lower mid-rangeDSC Programming DSC Programming To quit the DSC programming mode and store the adjustment Overview of the DSC factory settingsCLK AUTO/MAN Specifications AmplifierTuner CD playerTMC areas Bosch Gruppe
Top Page Image Contents