Alpine CDA-7893, CDA-7894, CDA-7892 owner manual Information, Case of Difficulty

Page 34

Information

In Case of Difficulty

If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.

Basic

No function or display.

Vehicle's ignition is off.

-If connected following instructions, the unit will not operate with the vehicle's ignition off.

Improper power lead connections.

-Check power lead connections.

Blown fuse.

-Check the fuse on the battery lead of the unit; replace with the proper value if necessary.

Internal micro-computer malfunctioned due to interference noise etc.

-Press the RESET switch with a ballpoint pen or other pointed article.

Radio

Unable to receive stations.

No antenna or open connection in cable.

-Make sure the antenna is properly connected; replace the antenna or cable if necessary.

Unable to tune stations in the seek mode.

You are in a weak signal area.

-Make sure the tuner is in the DX mode.

If the area you are in is a primary signal area, the antenna may not be grounded and connected properly.

-Check your antenna connections; make sure the antenna is properly grounded at its mounting location.

The antenna may not be the proper length.

-Make sure the antenna is fully extended; if broken, replace

the antenna with a new one.

Broadcast is noisy.

The antenna is not the proper length.

-Extend the antenna fully; replace it if it is broken.

The antenna is poorly grounded.

-Make sure the antenna is grounded properly at its mounting location.

CD

CD Player/Changer not functioning.

Out of operating temperature range +50˚C (+120˚F) for CD. - Allow the vehicle's interior (or trunk) temperature to

cool.

CD playback sound is wavering.

• Moisture condensation in the CD Module.

-Allow enough time for the condensation to evaporate (about 1 hour).

CD insertion not possible.

A CD is already in the CD player.

-Eject the CD and remove it.

The CD is being improperly inserted.

-Make sure the CD is being inserted following

instructions in the CD Player Operation section.

Unable to fast forward or backward the CD.

The CD has been damaged.

- Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism.

CD playback sound skips due to vibration.

Improper mounting of the unit.

-Securely re-mount the unit.

Disc is very dirty.

-Clean the disc.

Disc has scratches.

-Change the disc.

The pick-up lens is dirty.

-Do not use a commercial available lens cleaner disc.

Consult your nearest ALPINE dealer.

CD playback sound skips without vibration.

Dirty or scratched disc.

-Clean the disc; damaged disc should be replaced.

Error displays (built-in CD player only)

Mechanical error

-Press the c button. After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest ALPINE dealer.

MP3

MP3 is not played back.

Writing error occurred. The CD format is not compatible.

-Make sure the CD has been written in a supported format. Refer to "About MP3" on pages 26-27, then rewrite in the format supported by this device.

32-EN

Image 34
Contents CDA-7995/CDA-7894 Alpine CD Changers Give You More Contents XM Radio Operation Remote Control OperationMP3 Operation InformationPrecautions Never Attempt the Following Basic Operation Audio Mute Function Setting TimeDisplaying Time Setting the Treble Control Setting the Bass ControlAdjusting the built-in Crossover Example 1. Listening Position Front Left Seat About the Time CorrectionExample 2. Listening Position All Seats Example of Steps 2 and 3 Setting Bass FocusSetting the MX Mode Time Difference TableChanging the Audio Level Display Pattern Blackout Mode On and OffQuick Searching Function CDA-7995/CDA-7894 onlyDisplaying the Title/Text About Title and TextTitling Discs/Stations Erasing Disc Title/Station TitleChanging Lighting Color Setup OperationSwitching the Tuner Mode Dimmer ControlSetting the AUX Mode V-Link Turning Mute Mode On/OffScroll Setting Sound Beep Guide FunctionSetting the Defeat of the External Input Connecting to an External AmplifierCDA-7894/CDA-7893/CDA-7892 only Demonstration Adjusting Display ContrastCDA-7995 only Manual Storing of Station Presets Manual TuningAutomatic Seek Tuning Radio OperationAutomatic Memory of Station Presets Tuning to Preset StationsOpening and Closing the Movable display CD Player OperationPlayback Fast Forward and Backward Music Sensor SkipRepeat Play Scanning Programs When a 12-disc CD Changer is connectedX. Random Play Controlling CD Changer OptionalMulti-Changer Selection Playing MP3 Files MP3 OperationPlaying MP3 Files with the CD Changer Optional Selecting Folders File SearchPlaying MP3 Data Setting the Range of MP3 File SelectionWhat is MP3? About MP3Terminology Receiving XM Channels with the XM Receiver Optional XM Radio OperationChecking the XM Radio ID Number Category Search Storing XM Channel PresetsReceiving Stored XM Channels Changing the DisplayRemote Control Operation Controls on Remote ControlBattery Replacement Information Case of DifficultyNo Magzine Antenna Specifications FM Tuner SectionInstallation and Connections PrecautionsInstallation RemovalConnections 38-ENAntenna Receptacle Power Antenna Lead Blue To prevent external noise from entering the audio systemPage Limited Warranty ALPINE-1