Alpine 68-14470Z98-A owner manual Installation and Connections

Page 32

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

Be sure to disconnect the cable from the (–) battery post before installing your CDE-103BT. This will reduce any chance of damage to the unit in case of a short-circuit.

Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle’s electrical system.

When making connections to the vehicle’s electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDE-103BT to the fuse box, make sure the fuse for the intended circuit of the CDE-103BT has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your Alpine dealer.

The CDE-103BT uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized Alpine dealer for assistance.

Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

SERIAL NUMBER:

 

 

 

 

 

 

Please record the serial number of your unit in the space provided

INSTALLATION DATE:

 

 

 

 

 

below and keep it as a permanent record. The serial number or the

INSTALLATION TECHNICIAN:

 

 

engraved serial number is located on the bottom of the unit.

PLACE OF PURCHASE:

 

 

 

 

 

 

 

 

 

 

30-EN

Image 32
Contents CDE-103BT Page Contents Operating Instructions Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Getting Started Listening to Radio Setting TimePresetting Stations Manually Presetting Stations Automatically Tuning to Preset StationsPlayback Insert a disc with the label side facing upRepeat Play X. Random PlayAbout MP3/WMA/AAC Searching for CD TextQuick Search Terminology Defeat Sound SettingSetting the Bass Control Setting the Treble Control Adjusting the High Pass FilterSetting the Treble Center Frequency Setting the Treble LevelDisplaying Time Other FunctionsDisplaying the Text Using the Front AUX Input Terminal Turn the Rotary encoder to change the settingSelect Subwoofer Select Subw on or Subw OFFBluetooth Setting Sound CustomizingVisual Customizing External DeviceConnecting to an External Amplifier Power IC Setting the AUX+ Setup ModeSetting the AUX Name mode SpeakersSetup Before Using OperationSetting the Bluetooth Device Setting the Search ModeSetting the Received Calls automatically Auto Answer Deleting a Bluetooth Device from the listHands-Free Phone Control USB memory Optional IPhone/iPod Optional USB Memory Connection OptionalAbout MP3/WMA/AAC File of USB Memory IPhone/iPod models usable with this unitPress SOURCE/ to switch to the iPod mode Searching for a desired SongPress or to select the desired song Turn the Rotary encoder to select a desired songDirect Search Function Random Play Shuffle M.I.XTo cancel repeat play, select off with the above procedure Repeat OneSingle song is repeatedly played back Song is played back repeatedly Off Repeat OneInformation Case of DifficultyBasic RadioAudio IPodIndication for CD Player Indication for USB memoryIndication for all Modes Indication for iPod ModeBluetooth mode Specifications FM Tuner SectionInstallation and Connections Installation Mounting the MicrophoneRemoval Pull the unit out, keeping it unlocked as you do soTo iPhone/iPod Antenna To power antenna ConnectionsAntenna Receptacle Power Antenna Lead Blue Switched Power Lead Ignition RedFuse Holder 10A Front Output RCA Connectors Rear/Subwoofer Output RCA ConnectorsLimited Warranty This Warranty does not cover the following