Alpine 68-14470Z98-A Antenna Receptacle Power Antenna Lead Blue, Remote Turn-On Lead Blue/White

Page 35

Antenna Receptacle

Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna, if applicable.

•This lead should be used only for controlling the vehicle’s power antenna. Do not use this lead to turn on an amplifier or a signal processor, etc.

Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your amplifier or signal processor.

Audio Interrupt In Lead (Pink/Black)

Connect this lead to the Audio interface output of a cellular phone which provides ground shorting when a call is received.

Illumination Lead (Orange)

This lead may be connected to the vehicle’s instrument cluster illumination lead. This will allow the backlighting of this unit to dim whenever the vehicle’s lights are turned on.

Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle’s fuse box or another unused power source which provides (+)12V only when the ignition is turned on or in the accessory position.

Left Rear (+) Speaker Output Lead (Green)

Left Rear (–) Speaker Output Lead (Green/Black) Left Front (–) Speaker Output Lead (White/Black) Left Front (+) Speaker Output Lead (White)

Fuse Holder (10A)

Front Output RCA Connectors

RED is right and WHITE is left.

Rear/Subwoofer Output RCA Connectors

RED is right and WHITE is left.

MIC Input Connector

To Microphone.

RCA Extension Cable (sold separately)

Full Speed Connector

Control iPhone/iPod signals.

Connect this to an iPhone/iPod by using FULL SPEED Connection Cable (KCE-433iV) (sold separately) or to an external device (such as a portable player) by using conversion cable (KCE-237B) for building up the AUX IN (sold separately).

•Refer to “Setting the AUX+ SETUP Mode” (page 17).

AUX+ ON : When the external device is connected.

AUX+ OFF : When an iPhone/iPod is connected.

Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle’s battery.

Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.

Power Supply Connector

Right Front (+) Speaker Output Lead (Gray) Right Front (–) Speaker Output Lead (Gray/Black) Right Rear (–) Speaker Output Lead (Violet/Black) Right Rear (+) Speaker Output Lead (Violet)

FULL SPEED Connection Cable (KCE-433iV) (sold separately)

Front AUX Input Terminal

This terminal allows for input of audio from an external device (such as a portable player), using a commercially- available converter cable.

USB Connection Terminal

Connect USB memory (sold separately)

To prevent external noise from entering the audio system.

•Locate the unit and route the leads at least 10 cm away from the car harness.

•Keep the battery power leads as far away from other leads as possible.

•Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.

•If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors, contact them for further information.

•Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

33-EN

Page 34 Page 36
Image 35
Page 34 Page 36
Contents CDE-103BT Page Contents Operating Instructions Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Getting Started Listening to Radio Setting TimePresetting Stations Manually Insert a disc with the label side facing up Presetting Stations AutomaticallyTuning to Preset Stations PlaybackX. Random Play Repeat PlayAbout MP3/WMA/AAC Searching for CD TextQuick Search Terminology Defeat Sound SettingSetting the Bass Control Setting the Treble Level Setting the Treble ControlAdjusting the High Pass Filter Setting the Treble Center FrequencyDisplaying Time Other FunctionsDisplaying the Text Select Subw on or Subw OFF Using the Front AUX Input TerminalTurn the Rotary encoder to change the setting Select SubwooferExternal Device Bluetooth SettingSound Customizing Visual CustomizingSpeakers Connecting to an External Amplifier Power ICSetting the AUX+ Setup Mode Setting the AUX Name modeOperation Setup Before UsingDeleting a Bluetooth Device from the list Setting the Bluetooth DeviceSetting the Search Mode Setting the Received Calls automatically Auto AnswerHands-Free Phone Control USB memory Optional IPhone/iPod models usable with this unit IPhone/iPod OptionalUSB Memory Connection Optional About MP3/WMA/AAC File of USB MemoryTurn the Rotary encoder to select a desired song Press SOURCE/ to switch to the iPod modeSearching for a desired Song Press or to select the desired songRandom Play Shuffle M.I.X Direct Search FunctionSong is played back repeatedly Off Repeat One To cancel repeat play, select off with the above procedureRepeat One Single song is repeatedly played backRadio InformationCase of Difficulty BasicIndication for USB memory AudioIPod Indication for CD PlayerIndication for all Modes Indication for iPod ModeBluetooth mode FM Tuner Section SpecificationsInstallation and Connections Pull the unit out, keeping it unlocked as you do so InstallationMounting the Microphone RemovalConnections To iPhone/iPod Antenna To power antennaRear/Subwoofer Output RCA Connectors Antenna Receptacle Power Antenna Lead BlueSwitched Power Lead Ignition Red Fuse Holder 10A Front Output RCA ConnectorsThis Warranty does not cover the following Limited Warranty
Top Page Image Contents